Samsung HT-DB390 - Manual (Page 8)

Connect your pair of
wireless rear speakers,
(L) and (R), to the
wireless rear amplifier. 1 Insert the power plug into an outlet,
and then press the
POWER button
on the front panel.
• The Power Standby indicator will light up.
• To turn off the wireless rear amplifier,
press the
POWER button in Standby mode.
2
• Do not connect the wireless rear speakers
to the speaker outputs on the back of the
main unit. Malfunction may result.
• The wireless receiving antenna is built into
the wireless rear amplifier.
Keep the unit away from water and
moisture.
• For optimal listening performance, make
sure that the area around the proposed
wireless rear amplifier location is clear of
any obstructions.
• Sound will be heard from the wireless rear speakers in
DVD 5.1-CH or Dolby Pro Logic II mode only.
• In 2-CH mode, no sound will be heard from the wireless
rear speakers.
Reset the system if a communication failure occurs, or if the synchronizing signal indicator does not light up and the
"REAR CHK" message blinks on the main unit's display.
Reset the system while the main unit and the wireless rear amplifier (SWA-1000) are in Power Standby mode.
Resetting Wireless Communication
With the main unit turned off, press and
hold the remote control's
WIRELESS
button for 4 seconds.
• Press the button until the volume control indicator
lights up blue. (The indicator will turn off in 1 second.)
With the wireless rear amplifier turned
on, use a ball point pen or a pair of
tweezers to press the
RESET button
on the back of the unit 2 to 3 times.
2
1
You can turn the mood light on the wireless rear amplifier on or off, as well as change the light to one of 7 different
colors according to your preference.
Turning On the Mood Light
Press the POWER button on
the wireless amplifier.
• The Power Standby indicator on the
front panel will light up and the
mood light will turn on.
1
Press the COLOR MODE button.
• Each time the button is pressed, the color changes as
follows:
Blue ➞ Light Green ➞ Red ➞ Sky Blue ➞
Yellow ➞ Pink ➞ White
.
2
Turn on the main unit.
• The wireless rear amplifier's synchronizing signal
indicator will light up.
• If Power Standby mode continues, repeat Steps 1
to 3 above.
3
RESET Button
Back of Wireless Rear Amplifier
Back of Wireless Rear Amplifier
Wireless Rear Speaker (R) Wireless Rear Speaker (L)
14 13
CONNECTIONS
Caution
Caution
Connecting Wireless Rear Speakers
• Press the POWER button on the wireless amp.
The wireless rear amplifier and the mood light will turn off.
When the wireless amp is powered on again, the mood light will be blue.
• In Power Standby mode, press the ON/OFF button on the Wireless amp.
The mood light will light up or turn off with the last color selected.
Turning Off the Mood Light
Turning off the Wireless Amp and Mood Light
• Do not apply a strong shock to the wireless transmission antenna. Breakage may result.
• Do not touch the wireless transmission antenna during operation. Noise or interference to communications may result.
• Place the wireless rear amplifier at the rear of the listening position. If the wireless rear amplifier is too close to the main unit, some sound
interruption may be heard due to interference.
• If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, or any other device that uses the same frequency
(2.4GHz) near the system, some sound interruption may be heard due to interference.
• The transmission distance of radio wave is about 33 feet but may vary depending on your operating environment. If a steel-concrete wall or
metallic wall is between the main unit and the wireless rear amplifier, the system may not operate at all because the radio wave cannot
penetrate metal.
Stand the wireless transmission antenna to face upward for best communication status.
Caution
Note
When using the wireless transmission antenna