Skylink DIAL-ALERT AD-105 - Manual (Page 8)

1. Enter the current password (factory default password is 0000), then
press [PROG], display will show [P] meaning you are now in programming
mode.
2. Enter [5] which represents programming a device. You will see
[P5 Id codE].
3. Enter the Master Pin on the SC-001 then [B] [B].
4. After programming, the display will show “rEAdy” indicating it is now in
standby mode.
PROGRAM A SENSOR UNDER SENSOR OPERATING MODE
You may use the Dial Alert to notify you when there is a sensor activation.
You need to program the sensor signal to the Dial Alert, follow the
instructions below.
1. Enter the current password (factory default password is 0000), then
press [PROG], display will show [P] meaning you are now in
programming mode.
2. Enter [5] which represents programming a device. You will see
[P5 Id codE].
3. Activate the sensor so it sends an activation signal to the dialer.
4. Display shows [Id PLAy _] , enter the number of voice message you
have recorded, from [1] to [6]. When this sensor is activated, it will
playback the main voice message and the selected secondary
message. If you enter [0], no secondary message will be played.
Press [ ] for the dialer to accept your sensor.
5. After programming, the display will show “rEAdy” indicating it is now in
standby mode.
To program more devices to the Dial Alert, follow the instructions above.
You may program up to 16 different devices to the Dial Alert.
TESTING
SC-001 Mode
To test the operation, you may activate dialer by pressing the red panic
button on the SC-001. AD-105 will dial the phone numbers and playback
the voice message.
Sensor Mode
You can put the AD-105 in arm mode and activate the programmed sensor.
AD-105 will dial the phone numbers and playback the voice message.
Follow “Operations” – “Arming Sequence” to arm the AD-105.
STANDARD PROGRAMMING
– 14 – – 15 –
Do not program the phone number to police or fire dept directly into your Dial-Alert
unless you have checked with your local authorities. Please also inform all the
recipients that their phone numbers have been programmed into your dialer, so
they know exactly what happens when they receive your emergency message.
7. The Dial Alert is now in standby mode and the display shows “rEAdy” meaning
you have recorded a voice message and have a least one phone number
programmed.
You may sometimes need to insert pause period in a phone num-
ber so you can pause the dialing process, there are 2 types of pause periods.
1) Normal Pause 2) Pick up Pause
Normal Pause can be inserted to any part of the phone number and it will
simply pause the dialing process by the amount you have select. Press
[PROG] while you are programming a phone number, such as if you want to
enter a pause period after 123 while calling telephone number 1234567, you
need to program the phone number as 123[PROG]4567. Multiple pause
periods can be inserted within one telephone number.
Pick up Pause is useful when you know you will be calling something like
an answering machine, where after the phone is picked up, you don’t want
the emergency message to playback immediately. Therefore, you would
program a pause after the line is picked up. To insert a picked up pause, press
the “ ” button. The pick up pause duration is programmable. Please refer to
advanced programming. Only one pick up pause can be programmed within
one telephone number.
To program additional phone numbers, follow the above procedures by selecting
a different phone number locations, from 1 to 9.
You may review a programmed phone number by following the same
procedures as programming a phone number. Simply press [ ] when the
display shows the current setting instead of entering a new value allows you to
keep the programmed setting.
To erase a phone number from the Dial Alert, press [PROG] after step 3
above. That is after you select the phone number (from 1 - 9), Dial Alert will
show the programmed phone number. Pressing [PROG] now will delete this
phone number from the memory.
PROGRAM AN ALARM PANEL (Model SC-001) UNDER SC-001
OPERATING MODE
You may use the Dial Alert to notify you when there is a break-in or during an panic
situation. You need to program a panic signal from SC-001 Control Panel. To
program a Control Panel SC-001 to the Dial Alert, follow the instructions below.
STANDARD PROGRAMMING