Smeg AS 63 CS - Manual (Page 9)

9 - EN
Auxiliary function
Buzzer Cancel Models Equiped
Your machine will send out an buzzer warning
when the program comes to an end. If you
do not want to hear this buzzing, you need to
press the “Cancel Audio Warning” button. The
relevant LED will light up when this button is
pressed and an audio warning will not be given
when the program comes to an end.
Warning indicators
C
Warning indicators may differ
according to the model of your machine.
Filter cleaning
A warning LED will light up to remind filter
cleaning after the program finishes.
C
If the filter cleaning warning LED lights
up continuously, please refer to, “Solution
suggestions for problems”.
Water tank
A warning LED will light up at the end of the
program or when the tank is full with water. The
machine stops operating when this warning LED
lights up during a program running. To restart
the machine, please drain the water in the water
tank. Press “Start/Pause/Cancel” button to
start the program after you have emptied the
water tank. The warning LED goes off and the
program resumes operating.
Starting the Program
Press “Start/Pause/Cancel” button to start the
program. “Start/Pause/Cancel” button will
light up to indicate that the program has
started.
Progress of program
Progress of a running program is shown through
the program follow-up indicator.
At the beginning of every program step, the
relevant indicator LED will light up and light of
the completed step will turn off.
“Drying”:
- Drying level will be illuminated during the whole
drying process until the drying degree reaches “
Ready to Iron “.
“ Ready to Iron “:
- Starts to illuminate when the drying degree
reaches “ Ready to Iron “ step and remains
illuminated until the next step.
“ Ready to Wear “:
- Starts to illuminate when the drying degree
reaches “
Ready to Iron “ step and remains
illuminated until the next step.
“Final / Anti-creasing”:
- Illuminates when the program comes to an end
and anti-creasing function is activated.
C
If more than one LED light up or flash
concurrently, it means there is malfunctioning or
a failure (please see, Solution suggestions for
problems).
Changing the program after the program
has started
You can use this feature after your machine has
started to dry your clothes under higher or lower
temperatures.
For example;
Press and hold the “Start/Pause/Cancel” button for
about 3 seconds to “Cancel” the program in order
to select “Extra Dry” program instead of “Iron Dry”
program.
Select the “Extra Dry” program by rotating the
program knob.
Press “Start/Pause/Cancel” button to start the
program.
C
The program which is selected first will go on
even if the program selection button is moved
and another program mode is selected while
the machine is operating. You must cancel the
ongoing program in order to change the drying
program. (See, Ending the program through
canceling)
Adding/removing laundry in standby mode
If you want to add or remove laundry into/from your
machine after the drying program has started, put
the machine into “Pause” mode by pressing the
“Start/Pause/Cancel” button. Drying process will
stop. Open the door at Pause position and close
it again after adding or taking out laundry. Press
“Start/Pause/Cancel” button to start the program.
C
Any laundry added after the drying
process was started may cause the already
dried clothes in the machine intermingle with wet
clothes and the result will be wet laundry after the
drying process is over.
C
It is recommended to add laundry before
the program is started since it will increase the
program time and energy consumption.
Child-proof lock
There is a childproof lock to prevent any program
interruption due to the pressing of keys while
the program is on. The loading door and all
keys except the “On/Off” key on the panel are
deactivated when the child-proof lock is active.
In order to activate the childproof lock, press on the
“Start/Pause/Cancel” and “Cancel audio warning”
buttons simultaneously for 3 seconds.
To start a new program after
the program is over or to
interrupt the program, the
childproof lock should be
deactivated. To deactivate
the childproof lock, press
the same buttons for 3 sec.
C
2 beeps when activating and 1 beep
when deactivating the child-proof lock is heard.