Sherwood RD-8601 - Manual (Page 22)

22
ENGLISH
SETTING THE SPEAKER SETUP AUTOMATICALLY (AUTO SPEAKER SETUP)
Place the microphone on a flat level
surface at your normal listening position.
2
Press and hold down the SPEAKER SETUP
button on the front panel for more than 2
seconds to enter the auto speaker setup mode.
3
• If possible, use a tripod, etc. to attach the
microphone at the same height as your ears would
be when you are seated in your listening position.
• Ensure there are no obstacles between the speakers
and the microphone.
• Then “SET ALL S” is displayed.
• For your reference, the default settings for auto
speaker setup are as follows:
Speaker layout: ALL channels, Subwoofer: Yes,
CUToff frequency: 80 Hz
• When performing auto speaker setup according to
the default settings, skip the step and perform the
step .
• However, you can specify these settings according to
the number of speakers installed and speakers’
frequency characteristics with performing the step
.
• To cancel the auto speaker setup mode, press and
hold down the SPEAKER SETUP button on the front
panel for more than 2 seconds again.
• Press the POWER switch to enter the standby mode and then turn the power on.
Connect the optional microphone to the
SETUP MIC jack on the rear panel.(For
details, refer to “CONNECTING
MICROPHONE” on page 10.)
1
Before setting the speaker setup
• Auto Speaker Setup lets you avoid troublesome listening-based speaker setup and achieve good surround sound.
You should connect the microphone to the SETUP MIC jack so that this receiver can analyze the information from a series of
test tones emitted from speakers and can adjust the size, distance and sound level of each speaker automatically.
• If you want to personalize your speaker setup and channel level setup by making the settings manually, perform the
“SETTING THE SPEAKER SETUP MANUALLY” procedure on page 20, “Adjusting each channel level with test tone”
procedure on page 32 and “Adjusting the current channel level” procedure on page 33.
Note:
• Because the microphone for Auto Speaker Setup is designed for use with this receiver, to use the auto speaker setup
function, do not use a microphone other than the one supplied with this receiver.
VCR VCR
CH.SEL CH.SEL T/V T/V MUTE MUTE CH/LEVEL CH/LEVEL
MENU MENU SETUP SETUP
T.TONE .TONE OSD OSD
SLEEP SLEEP
AUTO AUTO
ADJUST ADJUST SPK SET SPK SET
1 2 3 4
8 7 6 5
9
M1 M1 M2 M2 M3 M3
0 +10 +10
MACRO MACRO
PARAMA ARAMATER
DSP DSP STEREO STEREO
ENTER ENTER
DIMMER DIMMER
DISPLA DISPLAY
DVD DVD SA SAT CBL CBL
CD CD AUX AUX TV TV
STANDBY
TUNE TUNE
PRESET PRESET PRESET PRESET P.SCAN .SCAN
TUNE TUNE RETURN RETURN
POWER ON POWER ON
REMOTE CONTROL RNC REMOTE CONTROL RNC-50A 50A
DEVICE SELECT
VOLUME
TUNER CD AUX TAPE
VIDEO 1 VIDEO 2 VIDEO 3
EXT. IN
AUD
or
POWER
ON/ OFF ON/STANDBY
STANDBY
POWER ON
VCR
CH.SEL T/V MUTE CH/LEVEL
MENU SETUP
T.TONE OSD
SLEEP
AUTO
ADJUST SPK SET
1 2 3 4
8 7 6 5
9
M1 M2 M3
0 +10
MACRO
PARAMATER
DSP STEREO
ENTER
DIMMER
DISPLAY
DVD SAT CBL
CD AUX TV
STANDBY
TUNE
PRESET PRESET P.SCAN
TUNE RETURN
POWER ON
REMOTE CONTROL RNC-50A
POWER ON STANDBY
VCR
CH.SEL T/V
MUTE CH/LEVEL
MENU SETUP
T.TONE OSD
SLEEP
AUTO
ADJUST SPK SET
1 2 3 4
8 7 6 5
9
M1 M2 M3
0 +10
MACRO
PARAMATER
DSP STEREO
ENTER
DIMMER
DISPLAY
DVD SAT CBL
CD AUX TV
STANDBY
TUNE
PRESET PRESET P.SCAN
TUNE RETURN
POWER ON
REMOTE CONTROL RNC-50A
SPK SET
SPEAKER
SETUP
VCR
CH.SEL T/V
MUTE CH/LEVEL
MENU SETUP
T.TONE OSD
SLEEP
AUTO
ADJUST SPK SET
1 2 3 4
8 7 6 5
9
M1 M2 M3
0 +10
MACRO
PARAMATER
DSP STEREO
ENTER
DIMMER
DISPLAY
DVD SAT CBL
CD AUX TV
STANDBY
TUNE
PRESET PRESET P.SCAN
TUNE RETURN
POWER ON
REMOTE CONTROL RNC-50A
ADJUST