Sony RM-VL1400T - Manual (Page 15)

15 GB Continued
Changing the characters
on the screen
You can change the A/V component names or functions,
or button function (label) displayed on the screen.
Characters and digits are input as follows by pressing the
number buttons.
1 1 c , c - c . c : c ; c < c = c > c ? c @ c /
2 A c B c C c a c b c c c 2 c À c Á c  c à c Ä c Å
c Æ c Ç c à c á c â c ã c ä c å c æ c ç
3 D c E c F c d c e c f c 3 c È c É c Ê c Ë c è c é c ê
c ë
4 G c H c I c g c h c i c 4 c Ì c Í c Î c Ï c ì c í c î c ï
5 J c K c L c j c k c l c 5
6 M c N c O c m c n c o c 6 c Ñ c Ò c Ó c Ô c Õ c
Ö c Ø c Œ c ñ c ò c ó c ô c õ c ö c ø c œ
7 P c Q c R c S c p c q c r c s c 7 c ß
8 T c U c V c t c u c v c 8 c Ù c Ú c Û c Ü c ù c ú c
û c ü
9 W c X c Y c Z c w c x c y c z c 9 c ´
Y
c ´y c ÿ
0 0 c N c b c B c ?b c B? c x c X c T c t c R
c r
-/-- ! c " c # c $ c % c & c ' c ( c ) c * c +
(1-)
ENT (space) c [ c \ c ] c ^ c _ c { c | c } c ˜ c · c ¡ c ¨
(2-) c ª c ´ c ‚ c º c ¿
Characters and digits are input as follows by pressing the
V/ v buttons.
A c B c C c D c E c F c G c H c I c J c K c L c M
c N c O c P c Q c R c S c T c U c V c W c X c Y
c Z c a c b c c c d c e c f c g c h c i c j c k c l c m
c n c o c p c q c r c s c t c u c v c w c x c y c z c
1
c 2 c 3 c 4 c 5 c 6 c 7 c 8 c 9 c 0 c À c Á c  c
à c Ä c Å c Æ c Ç c È c É c Ê c Ë c Ì c Í c Î c Ï c
Ñ c Ò c Ó c Ô c Õ c Ö c Ø c Œ c Ù c Ú c Û c Ü c
´
Y
c ß c à c á c â c ã c ä c å c æ c ç c è c é c ê c ë c
ì c í c î c ï c ñ c ò c ó c ô c õ c ö c ø c œ c ù c ú c
û c ü c ´y c ÿ c (space) c N c b c B c ?b c B? c x
c X c T c t c R c r c ! c " c # c $ c % c & c ' c
(
c ) c * c + c , c - c . c / c : c ; c < c = c > c ? c
@ c [ c \ c ] c ^ c _ c { c | c } c ˜ c · c ¡ c ¨ c ª c ´
c ‚ c º c ¿
6
Press the (light) button.
The display returns to the screen shown in step 2.
7
Press the (light) button or the RETURN
button twice.
The set mode closes, and the Remote Commander
returns to standby for operating the A/V components.
Notes on programming the signals for
an air-conditioner
About seasonal adjustments
If you change the settings of the air-conditioner for the
season, you have to programme the remote control
signals of the new settings on the Remote Commander.
If the power-on/off operation does not work
correctly
If the Remote Commander can only operate “ON” with one
button and “OFF” with another, while your air-conditioner’s
remote control can operate “ON/OFF” with a single button,
programme the signal on two buttons of the Remote Commander
as follows.
1 Clear the “learned” power-on/off signal on the
programmed button.
2 Reprogramme only the power-on signal of the air-
conditioner on the button by following the steps of
“Programming Signals of Another Remote Control”
(page 12).
3 Programme the power-off signal of the air-conditioner
on another button.
The two buttons of the Remote Commander have been
programmed with the power-on signal and the
power-off signal of the air-conditioner respectively, so
that you can operate the air-conditioner with the Remote
Commander.