Sony MKE-9020M - Manual (Page 27)

1-21
MVE-9000 IM
TP701 (G-7), TP801 (G-7), TP901 (E-7), TP1001
(E-7), TP1101 (K-6), TP1201 (K-6), TP1301 (J-6),
TP1401 (H-6), TP1501 (N-6), TP1601 (N-6), TP1701
(M-6), TP1801 (M-6) : ERR terminal
Used for design purpose.
TP3102 (C-6) : CKX (control timing) signal check
terminal
Use this terminal to check the CKX signal supplied from
mother board.
TP3103 (C-6) : FD signal check terminal
Use this terminal to check the FD signal supplied from
mother board.
TP3104 (C-6) : HD (horizontal sync) signal check
terminal
Use this terminal to check the HD signal supplied from
mother board.
TP3105 (C-5) : VD (vertical sync) signal check
terminal
Use this terminal to check the VD signal supplied from
mother board.
TP3401 (A-9), TP3402 (A-9), TP3403 (A-10),
TP3404 (A-9) : DBG3-0 check terminal
Used for design purpose.
<LEDs on the CPU-DR module> (C-11)
Refer to <LED on the CPU-DR module> in “1. CA-
54CFA Board”.
<Switches on the CPU-DR module> (C-11)
Refer to <Switches on the CPU-DR module> in “1. CA-
54CFA Board”.
D3401, D3402, D3403, D3404 (A-10) : DBG7-4
status LED
Used for design purpose.
ND3401 (A-10), ND3402 (A-11) : STATUS LED
VIF-28 board CPU status indication.
<Switches>
S3201 (A-8) : CPU CONFIG switch
Used for maintenance purpose.
S3401 (A-10) : SETUP switch
Used for maintenance purpose.
<Connectors>
CN3202 (A-7) : USB terminal
Used for debugging.
CN3203 (A-8) : TERMINAL pin
This pin is connected to the sub CPU control terminal and
used during maintenance. Conforms to RS-232C.
CN4001 (A-9) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
<TEST terminals>
E601 (H-4), E604 (C-9), E605 (N-2), E606 (C-7),
E607 (A-11), E608 (B-5), E609 (L-4), E610 (N-6),
E611 (E-4), E622 (F-7), E623 (A-2), E625 (J-6),
E626 (F-7), E627 (F-10) : GND terminals
Use these terminals as the earth point for measuring the
respective check terminals.
TP201 (C-3), TP603 (A-5) : + + + + +1.5 V check terminal
+1.5 V measuring terminal.
TP301 (E-3), TP602 (A-5) : + + + + +1.8 V check terminal
+1.8 V measuring terminal.
TP401 (G-3), TP604 (A-4) : + + + + +2.5 V check terminal
+2.5 V measuring terminal.
TP501 (J-3), TP605 (A-4) : + + + + +3.3 V check terminal
+3.3 V measuring terminal.
TP601 (A-4) : + + + + +12 V check terminal
+12 V measuring terminal.