Dcs c, Id s – Kenwood TM-271A User Manual
Page 56
49
9
• The available DCS codes are shown in the following
table.
s
e
d
o
C
S
C
D
4
0
1
3
2
0
5
6
0
2
3
1
5
0
2
5
5
2
1
3
3
3
1
4
5
6
4
2
1
6
1
3
7
5
2
0
1
7
0
4
3
1
2
1
2
1
6
2
2
3
3
3
2
4
6
6
4
4
2
6
2
3
7
6
2
0
2
7
0
3
4
1
3
2
2
3
6
2
3
4
3
1
3
4
3
0
5
7
2
6
4
3
7
1
3
0
3
7
0
5
4
1
5
2
2
5
6
2
6
4
3
2
3
4
6
0
5
1
3
6
3
4
7
2
3
0
4
7
0
2
5
1
6
2
2
6
6
2
1
5
3
5
4
4
6
1
5
2
3
6
4
5
7
6
3
0
4
1
1
5
5
1
3
4
2
1
7
2
6
5
3
6
4
4
3
2
5
4
5
6
3
4
0
5
1
1
6
5
1
4
4
2
4
7
2
4
6
3
2
5
4
6
2
5
2
6
6
7
4
0
6
1
1
2
6
1
5
4
2
6
0
3
5
6
3
4
5
4
2
3
5
4
6
6
1
5
0
2
2
1
5
6
1
6
4
2
1
1
3
1
7
3
5
5
4
6
4
5
3
0
7
3
5
0
5
2
1
2
7
1
1
5
2
5
1
3
1
1
4
2
6
4
5
6
5
2
1
7
4
5
0
1
3
1
4
7
1
2
5
2
5
2
3
2
1
4
4
6
4
6
0
6
3
2
7
3 Press [MENU] to store the new code or any other key
to cancel.
4 Press any key other than [MENU] to exit Menu Mode.
DCS C
ODE
ID S
CAN
This function scans through all DCS codes to identify the
incoming DCS code on the received signal. You may
find this useful when you cannot recall the DCS code
that the other persons in your group are using.
1 Press [F], [MENU] and turn the Tuning control to
select Menu No. 4 (DCS).
2 Press [MENU] (1s) to start the DCS Code ID Scan
function.
• While scanning, the decimal point between “DCS” and
the DCS code blinks.
• To quit the function, press any key.
• When a DCS code is identified, the identified DCS code
appears and blinks.
3 Press [MENU] to program the identified DCS code in
place of the current DCS code or press any other key
to exit the DCS Code ID Scan.
• Turn the Tuning control or press Mic [UP]/[DWN] while
the identified DCS code is blinking to resume scanning.
4 Press any key other than [MENU] to exit Menu Mode.
Note:
◆
DCS turns ON automatically when performing DCS Code ID
Scan, even if the current frequency is not set with DCS.
◆
Received signals are monitored through the speaker while
scanning is in progress.
◆
The transceiver continues to check the Weather Alert Channel
and Priority Channel during DCS scanning.
◆
DCS Code ID Scan does not scan the code if a signal is not
detected.