Care and cleaning – Kambrook KS200 User Manual

Page 6

Advertising
background image

6

WARNING: NEVER USE FINGERS, HANDS

OR OTHER UTENSILS TO PUSH FOOD DOWN

THE FEED CHUTE OR TO CLEAR THE FEED

CHUTE DURING OPERATION. ALWAYS USE

THE FOOD PUSHER PROVIDED.

Care aND CLeaNING

DISaSSembLING the JUICer
1. Ensure that the Kambrook Twin Speed Juicer

is turned off by switching the motor base to

the ‘0’ position at the control panel. Ensure the

appliance is switched off at the power outlet

and the power cord is unplugged.
2. Press the safety lock button and pull the safety

locking handle downwards.
3. Remove the food pusher from the feed chute

of the juicer cover.
4. Lift and remove the juicer cover.
5. Lift the filter bowl surround with the stainless

steel filter basket still in place away from the

motor base. The stainless steel filter basket will

lift off with it.
6. Lift the pulp container away from the motor

base.
WARNING: TAKE CARE WHEN HANDLING

THE STAINLESS STEEL FILTER BASKET AS

THE SMALL CUTTING BLADES AT THE BASE

OF THE FILTER BASKET ARE VERY SHARP.

MISHANDLING MAY CAUSE INJURY.
NOTE (For easier cleaning): Clean as you go and avoid

dried on juice or pulp residue. Immediately after each

use, rinse removable parts in hot water to remove wet

pulp. Allow parts to air dry. To minimise cleaning, line

the pulp container with a plastic freezer bag to collect

the pulp. Pulp can then be used in other dishes or as

compost for the garden or discarded.
CLeaNING the fILter boWL

SUrroUND, JUICer CoVer, PULP

CoNtaINer
1. Wash all parts in warm soapy water with a soft

cloth. Rinse and dry thoroughly.
NOTE: The pulp container is top shelf dishwasher safe

only
CLeaNING the fooD PUSher
The cover of the food pusher is removable to clean

residual juice that may have ingressed into the food

pusher during juicing.
1. To remove the cover from the food pusher, insert

a flat utensil (such as a screw driver) under the

indent located at the top of the food pusher and

lift the cover up.
2. Wash the cover and food pusher in warm soapy

water with a soft cloth. Rinse and dry thoroughly.

CLeaNING the fILter baSKet
For consistent juicing results always ensure that the

stainless steel filter basket is thoroughly cleaned

using the supplied cleaning brush.
1. Soak the stainless steel filter basket in hot

soapy water for approximately 10 minutes

immediately after juicing is completed. If pulp

is left to dry on the filter it may clog the fine

pores of the filter mesh thereby lessening

the effectiveness of the juicer.
2. Using the cleaning brush, hold the filter basket

under running water and brush from the inside

of the basket to the outer rim. Avoid touching

the small sharp blades in the centre of the filter

basket. After cleaning the filter basket, hold

it up towards a light to ensure the fine mesh

holes are not blocked. If the holes are blocked,

soak the filter basket in hot water with 10%

lemon juice to loosen the blocked holes.
NOTE: Do not place the stainless steel filter basket

in the dishwasher, soak in bleach or other abrasive

cleansers. Always treat the stainless steel filter basket

with care as it can be easily damaged.
WARNING: THE STAINLESS STEEL FILTER

BASKET CONTAINS SMALL SHARP BLADES

TO CUT AND PROCESS FRUITS AND

VEGETABLES. AVOID TOUCHING BLADES

WHEN HANDLING THE FILTER BASKET.
CLeaNING the JUICe JUG
Rinse the juice jug and froth separator under

running water.
Wash both parts in warm soapy water with a soft

cloth. Rinse and dry thoroughly.
NOTE: The juice jug and froth separator are top shelf

dishwasher safe only.
CLeaNING the motor baSe
1. Wipe the motor base with a soft, damp cloth

then dry thoroughly.
2. Wipe any excess food particles from the power

cord.
NOTE: Do not use abrasive scouring pads or cleaners

when cleaning the parts or motor base as they may

scratch the surface.
remoVING StUbborN or StroNG

fooD StaINS aND oDoUrS
Discolouration of the plastic may occur when using

strongly coloured fruit and vegetables. To help

prevent this, wash parts immediately after use. If

discolouration does occur, the plastic parts can be

soaked in water with 10% lemon juice or they can

be cleaned with a non abrasive cleaner.

Advertising