Kambrook Optimum Radiant Heater KRH600 - Manual (Page 3)

Set the control setting to the OFF
position then Unplug and allow heater to
cool down before cleaning or storing.
Do not use the heater with a
programmer, timer or any other device
that switches the heater on automatically,
since a fire risk exists if the heater is
covered or positioned incorrectly.
Use this heater only as described in this
instruction manual. Any other use not
recommended by the manufacturer may
cause fire, electric shock or injury and
voids all warranties.
Always move the heater with the handle
provided.
Regularly inspect the supply cord, plug,
control settings, air inlets and outlets and
main housing for any damage. If found
damaged in any way, immediately cease use
of the heater and return to Kambrook or
an authorized service agent for inspection.
The installation of a residual current
device (safety switch) is recommended to
provide additional safety protection when
using electrical appliances. It is advisable
that a safety switch with a rated residual
operating current not exceeding 30mA be
installed in the electrical circuit. See your
electrician for professional advice.
WARNING: In order to avoid
overheating do not cover the heater.
HOW TO OPERATE
Remove your heater from its carton;
unwind the cord to its full length.
Remove any element supports Guards (ie
foam or paper packing) by removing the
front guard screws, lift the guard upwards,
support and remove element supports.
Return the guard to the normal position
and replace screws.
Remove the warning sticker from the
front grill.
Read and follow the complete instructions
before plugging the unit into the 230-240
Volt supply.
Remove the castors from their storage
position on the base and using the same
securing screws fit the castors so that
they are positioned on the outer most
securing holes n the base of the heater.
The heater must never be operated without
the castors secured in the correct position
shown in figure 1.
Place the heater on a level surface in a
stable position. Make certain the heater
element control switch is in the OFF
position.
Remove the power cord from the storage
compartment on the rear, unwind the
cord fully and plug the power cord in a
240Volt outlet.
Use the rotary switch to select the
desired setting.The red indicator light will
illuminate when the setting is selected.
NEVER OPERATE THE HEATER
WITHOUT THE FRONT GRILL
SECURELY IN POSITION.
TEMPERATURE SETTING
The heater has 2 heat settings.
• Setting 1 operates the top and middle
elements at 1400 watts
• Setting 2 operates all three elements
at 2400 watts
The temperature knob (HEAT) acts as an
automatic thermostat and switches the top
element off during setting 1 and both the
top and bottom elements during setting 2:
• Turn both selector and temperature
knob to high / max settings
• Once a comfortable room
temperature has been reached, slowly
turn the temperature knob anti-
clockwise until you hear a click and
the top and bottom elements turn off.
(Note: during Setting 1 only the top element is
controlled with the thermostat)
• At this setting your heater will
automatically cycle high and low to
maintain the desired room
temperature
Note:There is a tip over switch fitted to this heater.
When the heater tips over, it will turn off
automatically.
CARE AND MAINTENANCE
• Always turn off the heater at the main
controls and then switch off at power
outlet before unplugging the heater
before cleaning.
• Use only a clean, dry cloth to clean the
external surfaces of the heater only.
• Do not attempt to remove the front
grill of the heater. The front grill is
designed to hinge upwards only and
never to be removed completely.
• Use a vacuum cleaner regularly to
remove dust and fluff from the element
and grill.
• If the unit has accumulated dust around
the elements and grill that cannot be
removed with the use of a vacuum
cleaner, have a qualified service agent
clean the unit. DO NOT operate the
heater in this condition.
• Do not attempt to open the case of the
heater at anytime, there are no
customer serviceable parts inside.
• When not in use, pack the heater in its
original box for best protection and
store in a cool, clean and dry location.
4 5
Fig 1