Kenwood Sovereign VR-5900 - Manual (Page 52)

Seting Up
Chapter Two: Setting Up
46
Setting Up on the Receiver
It is possible to set up the speakers on the receiver main
unit.
However, some of the setting items such as the controlled
device registration should also be set on the PowerTouch.
If setup is made on the PowerTouch, it is not necessary to
repeat any setup on the receiver side.
Therefore, it is recommended to perform setup on the
PowerTouch. This chapter describes the setup on the receiver
only as an alternative method in case the setup is not made
on the PowerTouch.
Do not operate the PowerTouch during the receiver setup.
Preparation for setup
Most of the receiver control buttons are accommodated
inside the panel door. Make the following preparation for
setup on the receiver.
1. Plug the power cord into a household power outlet.
2. Press the POWER switch to supply the main power. The
receiver now enters the STANDBY mode (in which re-
mote control is available). Then press the ON/STANDBY
button to turn the receiver ON.
3. Open the panel door.
Panel door
Speaker setup
1. Selecting the speakers
Selecting the SUBWOOFER:
1 Press the SET UP button (SOUND button) inside
the panel door until “SUBWOOFER OFF (or ON)”
message appears on the display ( for more than 2
seconds ).
2 Press the MULTI CONTROL ( fi/%) button to select
ON (when a subwoofer is used) or OFF (when not).
Selecting the FRONT speakers:
3 Press the SET UP button to display “FRONT NML/
THX (or FRONT LARGE)”.
4 Press the MULTI CONTROL ( fi/%) button to select
FRONT LARGE (large-sized speakers) or NML/THX
(normal-sized speakers).
If the SUBWOOFER is set to OFF, the FRONT speak-
ers are set automatically to LARGE and the CENTER
speaker selection display appears automatically.
Selecting the CENTER speaker:
5 Press the SET UP button to display “CENTER NML/
THX (or LARGE or OFF)”.
6 Press the MULTI CONTROL ( fi/%) button to select
CENTER LARGE (large-sized speaker), NML/THX
(normal-sized speaker) or OFF (no center speaker).
If the FRONT is set to NML/THX, the CENTER
speaker can be set to only either NML/THX or OFF.
Selecting the SURROUND speakers:
7 Press the SET UP button to display “SURR NML/
THX (or LARGE or OFF)”.
8 Press the MULTI CONTROL ( fi/%) button to select
SURR LARGE (large-sized speakers), NML/THX
(normal-sized speakers) or OFF (no surround
speaker).
When the FRONT is set to NML/THX, the SUR-
ROUND speakers can be set to only either NML/THX
or OFF.
When SURROUND OFF is selected, SURROUND
BACK is set automatically to OFF and the SW Re-
Mix setting menu is displayed.
If the SUBWOOFER is set to OFF, selecting SW RE-
MIX step will be skipped.
Selecting the SURROUND BACK speakers:
9 Press the SET UP button to display “S.BACK NML/
THX (or LARGE or OFF)”.
0 Press the MULTI CONTROL ( fi/%) button to select
S. BACK LARGE (large-sized speakers), NML/THX
(normal-sized or THX speakers) or OFF (no surround
speaker).
When the FRONT is set to NML/THX, the
SURROUND BACK speakers can be set to only either
NML/THX or OFF.
Press the DOOR OPEN/
CLOSE button to open
the panel door. To close
it, press the button again.
A SPEAKERS B I NPUT
MODE CD 2/TAPE 2
MONITOR
LISTEN
MODE THX
SET UP DISPLAY RF BAND RF
ON/OFF
SOUND
MULTI
CONTROL
fi % P.CALL MEMORY AUTO BAND fi %
Button layout