Installation – Kompernass KH 2391 User Manual
Page 10
12 GB/IE
L
Connecting to the vehicle‘s
12 V DC power supply
c Warning!
· Before connecting to the 12 V DC power supply of
a motor vehicle, consult the vehicle‘s operation
manual on how to maintain electrical safety!
· Ensure that when you establish the connection
to the 12 V DC power supply the connection
leads of the vehicle are not carrying any voltage.
Do not damage any safety equipment such as
the on-board computer or the alarm system of
the vehicle.
· Establish the connection to the 12 V DC power
supply with 3 x 1 A fuse holders!
· When installing in a motor vehicle you should
ensure that the vehicle cannot be operated and
is completely immobilised! Turn off the ignition
and park the vehicle with the handbrake applied!
· During installation you should use tools with a
double insulated handle!
· Avoid electrical short circuits when connecting
to the 12 V DC power supply.
· When establishing the connection between the
car radio and the 12 V DC power supply make
sure it is completely protected against moisture!
Tip! Use an ISO Plug.
• Please ensure that the intact 10 A flat blade
fuse
f
l
is inserted into the flat the blade fuse
socket
eu
as far as it will go.
• Guide the connection cables for the 12 V DC
power supply carefully out of the front of the
DIN assembly bracket
iq
.
• Establish the connection between the connection
cables of the ISO plug and the connection cables
of the 12 V DC power supply with the 3 x 1 A
fuse holders. Ensure that the connections of
the 3 x 1 A fuse holders do not cause any short
circuit and that the fixing screws are firmly
tightened.
• Using a 1 A fuse holder, connect the cable for
the 12 V DC constant current plug-in
fn
to the
connection cable for the 12 V DC constant current
of the motor vehicle.
• Optional - only if an electric aerial is connected:
Using one 1 A fuse holder each, connect the
cables for the 12 V DC ignition current
fp
and
electric aerial
fo
plug-ins to the connection
cable for 12 V DC ignition current of the vehicle.
In this manner the car radio and an electric aerial
can only use current from the vehicle when the
ignition is switched on.
• Using a biscuit connector, connect the cable for
the minus / earth connection plug-in in the
vehicle
fq
to the minus pole connection cable of
the vehicle (minus pole of the battery, which is
connected to the bodywork of the motor vehicle
as standard).
L
Connecting an amplifier
Tip! Use two cinch connection cables (insulation
and plug: white / red).
You can connect an amplifier to the device for
each loudspeaker channel (LINE OUT).
• Install the two cinch connection cables in the
vehicle according to their operating instructions.
• Pass two cinch connection cables to the amplifier
and carefully out of the front of the DIN assembly
bracket
iq
.
• Insert the red plug of the first cinch connection
cable as far as it will go into the OUT / REAR
cinch R plug jack (amplifier connection
[red / rear right])
fs
.
• Then insert the two red plugs of the first cinch
connection cable as far as it will go into the
REAR cinch R plug jack (amplifier connection
[red / rear right]) of the amplifier.
• Insert the white plug of the first cinch connection
cable as far as it will go into the OUT / REAR
cinch L plug jack (amplifier connection
[white / rear left])
gl
.
• Then insert the second white plug of the first
cinch connection cable as far as it will go into
the REAR cinch L plug jack (amplifier connection
[white / rear left]) of the amplifier.
• Insert the red plug of the second cinch
connection cable as far as it will go into the
OUT / FRONT cinch plug jack (amplifier
connection [red / front right])
go
.
Installation
KH2391_Content_UK.indd 12
05.09.2006 14:49:12 Uhr