Kenwood DMF-5020 - Manual (Page 24)

DMF-5020/DMF-3020/MD-203 (En)
24
Recording-related keys
AUTO / MANU. key
This key is used to select whether track numbers are to be
marked automatically during recording or they are to be
marked manually during or after recording. The track num-
bers can be used to locate the beginning of a track during
playback or programming tracks.
Select before starting recording.
AUTO
If a no-sound input has lasted for the time set for the AUTO TIME function
during recording, the track number will be incremented automatically by
“1”. Usually, use this position for recording. Use this mode when
recording all of the tracks in a CD. When recording music containing a
continuous section with a very low level, for example when recording
classic music, the track number may be incremented by “1” after such
a section. In this case, cancel the track number later. It is recommended
to use the MANUAL mode when recording such a kind of music.
During digital recording of CD, the track number is incremented auto-
matically by “1” according to the data contained in the digital informa-
tion. The no-sound blank is not detected.
When the CD track number is increased during manual search of a CD,
the track number recorded on the MD may sometimes fail to be
incremented.
A no sound track may sometimes created at the moment the played CD
stops.
MANUAL
With this setting, the MD track number is not incremented automatically
during recording. Track numbers can be marked either during editing (by
pressing the EDIT key) or after recording (by executing the TRACK DIVIDE
operation
‡ ). Even when “MANUAL” is set, the AUTO CUT and AUTO
PAUSE functions work if the “AUTO CUT” and “REC AUTO PAUSE”
settings are turned on.
This setting is convenient when recording a CD which has been recorded in
live or which contains very low-level sound such as a classical music CD.
Press in stop mode.
Press to monitor the sound being input from the source while the unit is in stop mode.
When the REC INPUT is DIGITAL, the sampling rate (48 kHz, 44.1 kHz, 32 kHz) of the input digital signal can be displayed by
pressing this key.
MONITOR key
Extinguished in “AUTO”
mode, lit in “MANUAL” mode.
“MONITOR” and “Sampling rate” litghts up
OVER ( − dB)
MANUAL
R
L
∞
15 9 12 7 5 1 3 40 30 21 18 0
SEARCH PGM
MONITOR
ANALOG
32kHz
2 1 3
48kHz
44.1kHz
DIGITAL
OVER ( − dB)
R
L
∞
15 9 12 7 5 1 3 40 30 21 18 0
SEARCH PGM
MONITOR
ANALOG
32kHz
2 1 3
48kHz
44.1kHz
DIGITAL
Main unit Remote control unit
(Remote control unit)
AUTO/MANU.
MONITOR
MONITOR
/DELETE
Each press switches the mode.
1 REC MODE : off
2 REC MODE : on
1
Switch the REC MODE on.
2
Select the setting adjustment mode.
3
Adjust the setting value.
The recording-related settings can be adjusted precisely by selecting the proper display modes.
÷ Step 3 consists of adjusting the setting of the “Setting adjustment
mode” selected in step 2.
÷ To end the setting adjustment, press the REC MODE/CHARAC. key
again.
Selecting the setting adjustment mode
The modes are switched by rotating the JOG DIAL.
AUTO CUT? : AUTO CUT on/off selection.
AUTO TIME? : Setting of the time for detecting a no-sound
blank section during automatic track number
marking.
AUTO LEVEL? : Automatic track number marking no-sound
blank detection level and SOUND SYNCHRO
REC, AUTO CUT and REC AUTO PAUSE sound
detection level setting
REC = WRITING? : Setting of the UTOC writing after recording.
To change another setting, press the SET key.
(This returns to step
2 above.)
REC MODE key
REC MODE/CHARAC.
4 ¢
JOG DIAL
4 ¢
SET
Set the selection.
4 ¢
JOG DIAL
4 ¢
SET
Set the selection.