Kambrook KCM1 - Manual (Page 3)

chocolate from either pouring lip, as
precisely as possible, into clean and dry
plastic moulds.
Using the Small Plastic Moulds:
Ensure the moulds are clean and dry.
Spread the melted chocolate in the
moulds with the spatula and pour any
excess chocolate from the moulds back
into the melting pot for re-use.
Allow the chocolate filled moulds to dry
and then cool in the refrigerator for
several hours or until the chocolate is
solid.When firmly set, turn the mould
upside down and gently press the
chocolate shapes out of the moulds
onto a clean dry plate or serving tray.
Store the solid chocolate shapes in a
clean, dry, air-tight container and avoid
over-handling as this may smudge or
soften the shapes.
Using the Large Heart Plastic
Mould:
Ensure the mould is clean and dry. Pour
approximately 150g melted chocolate into
the mould; the entire mould should be
thickly coated with chocolate. Use the
spatula or a pastry brush to evenly spread
and smooth the chocolate around the
mould.Allow to dry, then cool for several
hours until the chocolate shape is firmly
set. Cool in the refrigerator if desired.
Once set, turn mould upside down, and
gently press the chocolate heart out of
the mould onto a clean, dry surface.The
heart shaped mould can be used as an
edible dish for desserts or as decoration
on cakes. See recipe section page 7 for
suggested uses.
NOTE! The Chocolate Factory is designed solely for
melting chocolate.
NOTE! Chocolate should only be melted in the
melting pot. Do not melt chocolate directly in the
recess of the heating base.
TIPS FOR THE BEST USE
OF YOUR KAMBROOK
CHOCOLATE FACTORY
Do
Ensure that the melting pot and accessories
have been thoroughly washed in warm
soapy water with soft cloth. Rinsed and
dried thoroughly before assembly and use.
Ensure the Chocolate Factory is correctly
assembled before operating. Follow
assembly and operation instructions on
page 4.
Ensure the Chocolate Factory is used on
a clean, dry and level surface.
Use Setting 1 for keeping chocolate warm.
Use Setting 2 for melting chocolate.
Use the spatula provided to stir the
chocolate regularly in the melting pot
during melting.
Ensure that melting pot and moulds are
dry and clean. Never add water to the
chocolate or have wet moulds or a wet
melting pot as this will harden the
chocolate and it will not melt.
Use the accessories provided to help you
create decorative chocolates.
Store the solid chocolate shapes in a
clean, dry, air-tight container and avoid
over-handling as this may smudge or
soften the shapes.
IMPORTANT SAFEGUARDS
FOR ALL ELECTRICAL
APPLIANCES
Unwind the cord before use.
Do not let the cord hand over the edge
of a table or counter, touch hot surfaces
or become knotted.
This appliance is not intended for use by
young children or infirm persons unless
they have been adequately supervised by a
responsible person to ensure that they
can use the appliance safely.Young children
should be supervised to ensure that they
do not play with the appliance.
It is recommended to regularly inspect
the appliance. Do not use the appliance if
power supply cord, plug or appliance
becomes damaged in any way. Return the
entire appliance to the nearest authorised
Kambrook Service Centre for
examination and/or repair.
Any maintenance other than cleaning
should be performed at an authorised
Kambrook Service Centre.
This appliance is for household use only.
Do not use this appliance for anything
other than its intended use. Do not use
in moving vehicles or boats. Do not use
outdoors.
The installation of a residual current
device (safety switch) is recommended to
provide additional safety protection when
using electrical appliances. It is advisable
that a safety switch with a rated residual
operating current not exceeding 30mA be
installed in the electrical circuit supplying
the appliance. See your electrician for
professional advice.
BEFORE FIRST USE
Remove all packaging material and
promotional labels.
Wash the melting pot and accessories in
warm, soapy water, rinse and dry
thoroughly.
The heating base can be wiped with a
soft, damp cloth.
Assembling/Operating the
Kambrook Chocolate Factory
Ensure that the Chocolate Factory is
switched off by turning the selector control
to the off “O” position, the power
switched off at the power outlet and the
power plug is unplugged from the power
outlet.
Place the heating base on a flat, dry
surface. Insert the melting pot into the
recess of the heating base.
Pre-heat the appliance for 10 minutes by
inserting the power plug into power
outlet, switching on at the power outlet
and turning the selector control to Setting
2 for 10 minutes. (The Power Indicator
Light will illuminate on Settings 1 and 2).
Place the chocolate to be melted into the
preheated melting pot and stir regularly
during the melting process. Melting time
will vary with the amount and type of
chocolate being used.As an indication, it
will take approximately 10-15 minutes to
melt 250 grams of chocolate.
Once the chocolate is melted, turn the
selector control to the off “O” position.
Use the handle to remove the melting pot
from heating base and pour the melted
4 5