Kawasaki 691204 - Manual (Page 8)

R RE EM MO OV VIIN NG G A AN ND D IIN NS ST TA AL LL LIIN NG G T TH HE E A AB BR RA AS SIIV VE E C CU UT TT TIIN NG G W WH HE EE EL L
R RE EM MO OV VIIN NG G T TH HE E A AB BR RA AS SIIV VE E
C CU UT TT TIIN NG G W WH HE EE EL L::
1. Raise the abrasive wheel to its full open
position.
2. Remove the Stop Knob on the movable
blade guard.
3. Remove the movable blade guard
exposing the attaching hex socket-head
cap screw for the abrasive wheel.
4. Set the movable guard aside ensuring that it
doesn’t get bent or distorted.
5. Push the arbor shaft lock lever
and rotate the abrasive wheel until
the arbor lock engages locking
the wheel in place.
6. Hold the arbor shaft lock in
place and use a 5/16" (8mm) hex wrench or hex bit, remove the hex socket-head cap
screw by turning it counterclockwise. Also, remove the washer, outer flange, arbor
adapter (if used), abrasive wheel, and inner flange. See Figure 4.
IIN NS ST TA AL LL LIIN NG G T TH HE E A AB BR RA AS SIIV VE E
C CU UT TT TIIN NG G W WH HE EE EL L::
1. Place the hex socket-head cap
screw, washer, outer flange and
arbor adapter (if used) through the
hole in the new abrasive wheel.
2. Place the inner flange onto the
screw protruding to the back side
of the new abrasive wheel.
3. Holding the new abrasive wheel in
one hand, align the screw into the
threaded hole in the arbor.
4. Push in the arbor shaft lock
lever and turn the new
abrasive wheel until the
shaft locks.
13
T TO OO OL LS S R RE EQ QU UIIR RE ED D FFO OR R A AS SS SE EM MB BL LY Y
The tools, pictured, are supplied by the
customer.
It is highly recommended that the 14" Cut-off
saw be securely mounted to a tool stand. This
is to prevent excessive vibration during use.
Mount the Cut-off saw to the tool stand by:
1. Most tool stands have pre-drilled holes to
accommodate a variety of tools.
2. If the tool stand does not have an exact
match for the holes, try to align the tool
base with as many pre-drilled holes as pos-
sible. Mark and drill new holes for mounts
that have missing holes.
3. Insert four 1/4" X 20 screws and washers
through the underside of the tool stand and
up through the rubber feet on the base of
the Cut-off saw. The length of the screws should be 1" (25mm).
4. Tighten the screws securely.
U UN NL LO OC CK KIIN NG G T TH HE E C CU UT T--O OFFFF S SA AW W
D Diisscco on nn neecctt tth hee aab brraassiivvee C Cu utt--o offff ssaaw w ffrro om m tth hee A AC C p po ow weerr
sso ou urrccee eelliim miin naattiin ng g aan nyy aacccciid deen nttaall ssttaarrttiin ng g o off tth hee m mo otto orr..
PHILLIPS SCREWDRIVER
ADJUSTABLE WRENCH
PROTRACTOR
HEX (ALLEN) WRENCHES
FIGURE 3. REMOVING BLADE GUARD
T TO O C CA AR RR RY Y T TH HE E C CU UT T--O OFFFF S SA AW W::
Fold down head to base and rotate
the motor arm release to lock head.
T TO O U UN NL LO OC CK K T TH HE E C CU UT T--O OFFFF S SA AW W::
To unlock tool and raise head
depress motor arm slightly and
rotate motor arm release. The motor
arm will pivot upward. See Figure 2.
FIGURE 2. UNLOCKING THE CUT-OFF SAW
LOCK
RELEASE
14
FIGURE 4. REMOVING/INSTALLING THE CUTTING WHEEL