Kawasaki 691204 - Manual (Page 9)

3. Using a 5/16" (8mm) hex wrench or hex bit, turn the two hex socket-head cap
screws clockwise to securely tighten.
4. Using a 5/16" (8mm) hex wrench or hex bit, turn the two hex socket-head cap
screws counterclockwise and remove them.
5. Slide the stationary portion of the work vise over the last threaded hole in the
Cut-off saw base.
T Th hee aan ng glleed d ccu utt sseettttiin ng gss o on n tth hee ffeen nccee b baassee aarree o on nllyy
aap pp prro oxxiim maattee sseettttiin ng gss.. A Allw waayyss cch heecckk tth hee aaccccu urraaccyy o off aan ng glleed d ccu utt sseettttiin ng gss
u ussiin ng g aa p prro ottrraacctto orr o orr b beevveell g gaau ug gee..
5. Hold the arbor shaft lock in place and
use a 5/16" (8mm) hex wrench or hex
bit, turn the hex socket-head cap screw
clockwise to tighten.
6. Tighten the hex socket-head cap screw
securely into the motor arbor. See
Figure 4.
7. Replace the movable blade guard
exposing the covering hex socket-head
cap screw for the abrasive wheel.
8. Replace nut on the movable blade
guard.
D Do o n no ott o ovveerr ttiig gh htteen n tth hee h heexx sso occkkeett--h heeaad d ssccrreew w.. O Ovveerr ttiig gh htteen niin ng g tth hee ssccrreew w ccaan n
ccaau ussee tth hee aab brraassiivvee w wh heeeell tto o ccrraacckk rreessu ullttiin ng g iin n p prreem maattu urree ffaaiillu urree.. T Th hiiss cco ou ulld d
ccaau ussee tth hee aab brraassiivvee w wh heeeell tto o b brreeaakk aan nd d ffllyy o offff tth hee aarrb bo orr ssh haafftt w wh heen n tth hee ttrriig g--
g geerr iiss een ng gaag geed d.. FFaaiillu urree tto o aad dh heerree tto o tth hiiss W Waarrn niin ng g cco ou ulld d ccaau ussee d daam maag gee tto o tth hee
C Cu utt--o offff ssaaw w aan nd d sseevveerree iin njju urryy o orr eevveen n d deeaatth h tto o tth hee o op peerraatto orr..
U Ussee o on nllyy aa 1 14 4"" d diiaam meetteerr aab brraassiivvee C Cu utt--o offff w wh heeeell rraatteed d tto o aa m miin niim mu um m 4 40 00 00 0
R RP PM M.. C Cu utt--o offff w wh heeeellss tth haatt d do o n no ott m maattcch h tth hee m mo ou un nttiin ng g h haarrd dw waarree,, eexxcceeeed d aa
m maaxxiim mu um m 4 44 40 00 0 R RP PM M o orr ffaallll b beello ow w tth hee m miin niim mu um m 4 40 00 00 0 R RP PM M m maayy ssu ussttaaiin n
p prreem maattu urree w weeaarr o orr b brreeaakkaag gee aan nd d ffllyy o offff tth hee C Cu utt--o offff ssaaw w o orr rru un n eecccceen nttrriiccaallllyy
rreessu ullttiin ng g iin n aa llo ossss o off cco on nttrro oll.. FFaaiillu urree tto o aad dh heerree tto o tth hiiss W Waarrn niin ng g cco ou ulld d ccaau ussee
d daam maag gee tto o tth hee C Cu utt--o offff ssaaw w aan nd d sseevveerree iin njju urryy o orr eevveen n d deeaatth h tto o tth hee o op peerraatto orr..
A AD DJJU US ST TIIN NG G T TH HE E W WO OR RK K V VIIS SE E
The work vise is located on the base of the Cut-off saw. The vise is made up of two
parts: (1) a stationary fence which can be loosened and rotated from 0˚ to 45˚
degrees and (2) a movable clamp with an adjustable screw handle and a quick-
release lock.
The work vise will also move toward the rear of the base to allow larger workpieces to be
cut. To set up and adjust the work vise, follow the directions below. See Figure 6.
15
FIGURE 5. REMOVING/INSTALLING
THE CUTTING WHEEL
FIGURE 6. ADJUSTING THE
WORK VISE
1. Using a 5/16" (8mm) hex wrench or hex bit, turn the
two hex socket-head cap screws counterclockwise
to loosen.
2. Rotate the work vise fence to the desired the angle
by aligning the gauge on the vise base with the indi-
cator groove in the Cut-off saw base.
FIGURE 7.
CHECKING ANGLE
CUT SETTINGS
6. Install one of the hex socket-
head cap screws into the hole.
DO NOT TIGHTEN AT THIS
TIME.
7. Align the second hole of the
work vise base with another
threaded hole in the Cut-off
base.
8. Install the second hex socket-
head screw into the hole.
9. Using a 5/16" (8mm) hex
wrench or hex bit, turn the
two hex socket-head cap
screws clockwise to loosen.