Kenwood XD-700 - Manual (Page 55)

XD-750/700/550/500 (En)
5 5
Preparation section
Basic
section
Application section
Knowledge sections
Be especially careful in the following conditions:
÷
When the unit is brought from a cold place to a warm place, and there
is a large temperature difference.
÷
When a heater starts operating.
÷
When the unit is brought from an air-conditioned place to a place of
high temperature with high humidity.
÷
When there is a large difference between the internal temperature of
the unit and the ambient temperature, or in conditions where conden-
sation occurs easily.
Cleaning the head section
There are precisely aligned parts around the heads, including the tape guides.
When cleaning, pay special attention so as not to apply shock to them.
Beware of condensation
When water vapor comes into contact with the surface of a cold
material, condensation is produced.
If condensation occurs, correct operation may not be possible, or
the unit may not function correctly.
This is not a malfunction, however, and the unit should be dried-out.
(To do this, turn the ON/STANDBY switch ON and leave the unit as it
is for several hours.)
Dolby noise reduction manufactured under license from Dolby Labo-
ratories Licensing Corporation.
“DOLBY” and the double-D symbol are trademarks of Dolby Labora-
tories Licensing Corporation.
Important Items
Note Note
Reference
Maintenance
Demagnetizing the head
When the recording / playback head is magnetized,
the sound quality will deteriorate. In such a case,
demagnetize the head using a commercially avail-
able demagnetizer (head eraser).
Cleaning the heads and peripheral compo-
nents
For maintaining the best condition of the deck and
for longer service life, always keep the heads (re-
cording / playback / erase), capstan and pinch roller
clean. To clean them, perform the following:
1. Open the cassette holder.
2. Using a cotton swab dipped in alcohol, clean the
head (recording / playback / erase), capstan and
pinch roller carefully.
Note related to transportation and movement
(CD player)
Before transporting or moving this unit, carry out the following
operations.
1. Turn the power ON but do not load a disc.
2. Ensure that the display is as shown below.
3. Wait for a few seconds then turn power off.
REV.MODE
C D N O D I s C
EX . BASS
1 2 3
B
RUNNING
INDICATOR
EQ.
CLASSIC
MANUAL
POP ROCK
VOL.
6
7
8
9
10
11 12 13
14
15
16
1
2
3 4 5
Sound Retrieval System manufactured under licence from SRS Labs,
Inc. “SOUND RETRIEVAL SYSTEM” and the SRS Symbol
are
trademarks of SRS Labs, Inc.
Purchase of this product does not convey the right to sell recordings
mode with the SOUND RETRIEVAL SYSTEM.
Maintenance of the set
When the front panel or case becomes dirty, wipe with a soft, dry
cloth. Do not use thinner, benzine, alcohol, etc. for these agents may
cause discoloration.
In regardto contact cleaner
Do not use contact cleaners because it could cause a malfunction.
Be specially careful not to use contact cleaners containing oil, for
they may deform the plastic component.
When your unit needs to be repaired, bring the entire set (Speakers
excluded) to your dealer.
Capstan
Pinch roller
Head
Tape guides
Cotton swab
Stored contents which are
cleared immediately when
power plug is unplugged from
power outlet Clock display
Stored contents which are
cleared in at least a day after
power plug is unplugged from
power outlet Amplifier
POWER status (ON or OFF)
Input selection
Volume control value
Equalizer’s manual memory cre-
ated by the user
SRS 3D level
Tuner unit
Receiving band
Frequency
Preset stations
Program timer setting contents
Cassette deck unit
Transport direction
DOLBY NR
Reverse mode
Memory backup function