Loewe Auro 2216 PS - Manual (Page 9)

9 -
First installation
Wiring Loewe Flat TV – Auro – Individual Sound/Tremo
Connect the cables as shown in the graphic:
Connect the Auro to socket AV of the Loewe Flat TV. If your Loewe TV set has
three AV sockets, use socket AV3.
You must use a Euro-AV cable in which all contacts are connected with each
other (1-fold as in the case with the enclosed cable).
To get a better picture quality, use a three-wire cinch cable and connect it to
Auro “COMPONENT VIDEO OUT“ and “SD/HD-COMPONENT IN“ of the TV set.
Pay attention to the exact polarity of the Y/Cb/Cr signals. In addition you have
to switch the “VIDEO OUT SELECTOR“ switch on the back of the Auro to the
“COMP.“ position.
Letters are embossed on the sides of the plugs on the six-wire cinch cable:
gray plug: ”C” for center channel; black plug: ”LFE” for subwoofer; red plug:
”FR” for front right or ”SR” for surround right; white plug: ”FL” for front left or
”SL” for surround left.
Two-wire (thin) cubic plug cable from Auro to the “Master” socket on Individ-
ual Sound/Tremo (connect the end of the cable with kink protection to Auro).
The cubic plugs are secured in the socket by a lug. You have to press down the
lug first before you can remove the cubic plug. •
•
•
•
•
For TV as center loudspeaker use a cinch cable to connect “AUDIO IN C“ on
the TV set with “PRE OUT C“ on the DVD Preceiver (the connection of the gray
plug “C“ between Auro and Individual Sound/Tremo is omitted). In addition,
you have to move the ”Center to” switch on the back of Individual Sound/Tre-
mo to the ”TV” position (switch must be pressed); see the separate operating
manual for Individual Sound/Tremo.
To play the TV sound over Auro/Individual Sound/Tremo, connect the digital
audio output of the TV set “AUDIO DIGITAL OUT“ with the “DIGITAL IN“ input
from Auro with a cinch cable.
When establishing the L-Link, Auro and the TV must be in the powerless state,
otherwise, these devices cannot identify each other after switching on; for
L-Link see page 7.
You can connect an additional external analogue source to the analogue audio
input AUX 1 IN.
Audio cable cinch -> SCART (available in specialised trade) for use of the
component signal and “TV as centre loudspeaker“ - see note on page 4. •
•
•
•
•
PREOUT
L C R L L
SL LFE SR R R
TO TV
AUX1 IN
DIGITAL
IN
DIGITAL
OUT TV
L-LINK 12V / 15mA
EXT
AUX OUT AUX 2
ON
Line IN
Power OUT
OFF
Bass Intensity
Center to
System connector
230V~50/60Hz
Surr.
Front
Right
Surr.
Front
Subw. Left
Right Center Left
Slave
Master
R
R
L
C
L
Phase
Min. Max.
TV Sat 0 180
Loewe Individual Sound/Tremo
Loewe Flat-TV
Loewe
Auro
AV2-SCART
SERVICE
CENTER AUDIO OUT L/R
DIGITAL OUT COMPONENT IN
COMPONENT VIDEO OUT
Y
Pb
Pr
L SL SR R C LFE
L SL SR R C FLE
Audio cable cinch -> SCART
(available in specialised
trade)
only required with TV as
centre spreaker
L-Link-cable
Cubic plug cable
Component Video
(available in specialised
trade)
EURO-AV-cable
Six-pole cinch
Surround speaker system
Digital audio TV -> Auro