Lincoln Electric VANTAGE 400 User Manual
Vantage, Svm182-a, Service manual
Advertising
VANTAGE
®
400
SVM182-A
April, 2011
For use with machines having Code Numbers: 11186, 11462
SERVICE MANUAL
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 888.935.3877 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
• World's Leader in Welding and Cutting Products •
Copyright © Lincoln Global Inc.
VANT
AGE 400
LINCOLN
ELECTRIC
Safety Depends on You
Lincoln arc welding and cutting equip-
ment is designed and built with safety
in mind. However, your overall safety
can be increased by proper installation
... and thoughtful operation on your
part. DO NOT INSTALL, OPERATE
OR REPAIR THIS EQUIPMENT
WITHOUT READING THIS MANU-
AL AND THE SAFETY PRECAU-
TIONS CONTAINED THROUGH-
OUT. And, most importantly, think
before you act and be careful.
RETURN TO MAIN MENU
Advertising
Table of contents
Document Outline
- Master Table of Contents
- Safety
- Section A - Installation
- Section B - Operation
- Section C - Accessiories
- Section D - Maintenance
- Section E - Theory of Operation
- Section F - Troubleshooting and Repair
- Symptoms
- Major mechanical or electrical damage is evident.
- No welding output or auxiliary power. The engine operates normally.
- No welding output in any mode. The auxiliary output is normal. The engine operates normally.
- No output in PIPE MODE. Outputs normal in other modes.
- VRD lights don’t light up.
- No auxiliary power at one or more receptacles or at the 14 pin Amphenol. Weld output is normal and the engine operates normally.
- The machine has low welding output and low auxiliary output.
- The machine will weld but the welding arc is “COLD”. The engine runs normally and the auxiliary power is normal.
- The machine will weld but the welding arc is “COLD”. The engine runs normally and the auxiliary power is normal. (continued)
- The machine welds but it will not maintain a steady output.
- The machine welds but it will not maintain a steady output. (continued)
- The weld output can not be adjusted with the front panel output control knob in one or mode weld modes. The weld output terminals have normal OCV (open circuit voltage). The AC auxiliary power is normal and the engine operated normally.
- The machine front panel output control is still active when the remote control unit is connected to one of the Front Panel Amphenols.
- The machine seems to be locked into the “CC-stick” mode of operation.
- The arc quality is poor with excessive spatter. The arc heat can be controlled and maintained normally, the auxiliary output is normal and the engine operates normally.
- The machine welds normally in all modes and the range of weld output seems normal, but one or both of the front panel displays is blank, incorrect welding value, or displays parts of numbers.
- A control cable type feeder does not function when connected to the 14 pin amphenol. Machine operates normally in the “CC-STICK” mode and has normal AC auxiliary output.
- An Across-the-Arc type wire feeder does not function when connected to the weld output of the machine. The Vantage® operated normallyin the CC-STICK mode, and has normal AC auxiliary output.
- The engine will not crank when the start button is pushed.
- The battery does not stay charged.
- The engine cranks when the startbutton is pressed but will not start.
- The engine starts but shuts down immediately when the start button is released.
- The engine shuts down shortly after starting.
- The engine shuts down shortly after starting.
- The engine shuts down shortlyafter starting and trips the battery circuit breaker (CB5).
- The engine will not develop ful lpower.
- The engine will not idle down to low RPM. The machine has normal weld and auxiliary output.
- The engine will not idle down to low RPM. The machine has normal weld and auxiliary output. (continued)
- The engine will not idle down to low RPM. The machine has normal weld and auxiliary output. (continued)
- The engine will not go to high idle when using auxiliary power. Auxiliary power is normal when the idler switch is in the “HIGH” idle position, the automatic idle function works properly when welding.
- The engine will not go to high idle when striking arc. The automatic idle system functions normally when using auxiliary power. Welding and auxiliary outputs are normal when the idle switch is in the “HIGH IDLE” position.
- The engine will not go to high idle when attempting to strike and arc, or when a load is applied to any of the auxiliary power receptacles.
- The engine goes to low idle, but will not stay low idle.
- Section G - Electrical Diagrams