Liebherr 7082 218-03 - Manual (Page 15)

16
BN/BNes...6
Operation and control elements
BioCool
The BioCool button switches the BioFresh compartment to
maximum cooling.
It is recommended particularly if you wish to cool large quan-
tities of food, freshly baked cakes or meals rapidly.
W
Switching on: Press the BioCool button
bl
briefly so that
it lights up.
Note: The BioCool function uses slightly more energy. After
approx. 6 hours, however, the electronic control system
switches back automatically to normal energy-saving
operation.
If required, the BioCool function can be switched off soo-
ner.
W
Switching off : Press the BioCool button again until it
goes out.
SuperFrost
Fresh food should be frozen to the core as rapidly as pos-
sible. Frozen food can also be given a cold boost. This is
provided by the SuperFrost facility
4 and ensures that the
nutritional value, appearance and flavour of the food remain
intact.
W
The maximum amount of food which can be frozen in
24 hours is shown on the type plate ("Freezing capacity
... kg/24h"), fig.
A3, pos.
4 . This amount varies accord-ing
to the model and climate rating.
See "Freezing with SuperFrost" for more information.
Power failure/FrostControl display
If appears in the display, this means that the free-
zer temperature has risen too high during the last few
hours or days due to a power failure.
W
If you press the audible warning on/off button 5
whilst the display is reading , the highest temperature
registered during the power failure will be displayed.
Check the quality of the food and its suitability for con-
sumption in case it has become too warm or even de-fros-
ted.
- The highest temperature will appear for approx. 1 minute.
After that, the actual temperature in the freezer will re-ap-
pear. The "highest temperature" display can be
switched off by pressing the audible warning on/off button.
Once the power is re-instated, the appliance will continue to
operate at the most recent temperature setting.
Additional functions
In set-up mode you can set the child-proof lock and adjust
the brightness of the display*:
Activating set-up mode:
W
Press SuperFrost button for approx. 5 secs - the Super-
Frost button flashes - the display shows c for child-proof
lock.
Note: the value to be altered flashes.
W
Select the required function by pressing the Up/Down
button:
c = child-proof lock or h = brightness.
W
Now select/acknowledge function by pressing SuperFrost
button briefly:
• For c = child-proof lock, press the Up/Down
button to select c 1 = child-proof lock on or
c 0 = child-proof lock off and acknowledge with
the SuperFrost button. When the symbol
6
is lit,
the child-proof lock is activated.
• For h = brightness, press Up/Down button to
select h 1= minimum to h5 = maximum bright-
ness and acknowledge with the SuperFrost
button.
Exit set-up mode:
W
To exit the set-up mode, press the On/Off button; after
2 mins. the electronic system switches over automatically.
- The normal operating mode is activated again.
Interior light
This switches off automatically after the door has been ope-
ned for approx. 15 minutes. If it does not switch on when the
door is opened briefly, but the temperature display is wor-
king, the bulb may be defective.
Replacing the bulb:
W
Bulb data: max. 25 W; current and voltage must agree
with the details on the type plate. Only use bulbs of the
same size. Bulb fitting: E 14.
W
Switch off the appliance. Disconnect from the mains or
remove or unscrew the fuse.
W
Press the light cover together at the sides as in fig. F1 (1).
Lift it out and unclip at back (2).
W
Replace the bulb as in fig. F2. To counteract the friction of
the lock washer, turn the bulb with slightly more pressure.
When inserting the new bulb, ensure that the lock washer
is properly in place in the lamp socket.
W
Clip the back end of the cover in and clip the sides into
place.
BioCool