Lincoln Electric COMMANDER 300 IM601-A - Manual (Page 28)

C-1 ACCESSORIES C-1
OPTIONAL FIELD INSTALLED
ACCESSORIES
K802R POWER PLUG KIT - Provides a plug for each
receptacle. Use K802N for code numbers above
10500.
K802N POWER PLUG KIT - Provides four 120V plugs.
K857 28 ft. (8.5 m) or K857-1 100 ft. (30.4 m)
REMOTE CONTROL - Portable control provides same dial
range as the output control on the welder from a location up
to the specified length from the welder. Has convenient plug
for easy connection to the welder. The Commander 300 is
equipped with a 6 pin connector for connecting the remote
control and a toggle switch for selecting “LOCAL” output con-
trol or “REMOTE” output control.
K704 ACCESSORY SET - Includes 35 feet (10 m) of
electrode cable and 30 feet (9 m) of work cable, head-
shield, work clamp and electrode holder.
Cable is
rated at 500 amps, 60% duty cycle.
K953-1 TWO WHEEL TRAILER - For road, in-plant
and yard towing. Road towing with optional fender &
light kit. (For highway use, consult applicable federal,
state and local laws regarding possible additional
requirements)
K953-1 Trailer K958-1 Ball Hitch
K958-2 Lunette Eye Hitch K959-1 Fender & Light Kit
K965-1 Cable Storage Rack
K887-1 ETHER START KIT - Provides maximum cold
weather starting assistance for frequent starting below 10
o F
(-12.2 o C). Required Ether tank is not provided with kit.
S24647 SPARK ARRESTOR KIT - Easily mounts to
standard muffler. Approved by U.S.D.A. Forest Service.
K1604-1 OIL DRAIN KIT - Includes ball valve, hose
and clamp.
K1690-1 (1 Duplex) GFCI Kit - Includes one UL
approved 115V ground fault circuit interrupter duplex
type receptacle with cover and installation instructions.
Replaces the factory installed 115V duplex receptacle.
The receptacle of the GFCI duplex is rated at 20 amps,
the maximum total current from the GFCI duplex is lim-
ited to 20 amps. Two kits are required.
K1596-1 Dual Output Meters and Gauges - Dual out-
put meters provide preset ability of voltage for wire
welding and current for stick welding. Measures b o t h
current and voltage when welding. Gauges include:
battery ammeter, engine temperature, and engine oil
pressure. Fuel gauge is not available in kit form.
K1597-1 42vac Transformer Kit. - For products requir-
ing 42 VAC power source.
RECOMMENDED OPTIONAL EQUIP-
MENT
STICK
K704 Accessory Kit which includes:
• Electrode holder and cable.
• Ground clamp and cable.
• Headshield.
K857 Remote Control Kit is optional for remote cur-
rent control.
TIG
Magnum TIG Torch
Magnum Parts Kit and Argon gas
K930-ALL TIG Module (not required for scratch start
DC TIG welding)
K936-1 Control Cable
K870 Foot Amptrol
Also available:
K963-1/-2 Hand Amptrol
K814 Arc Start Switch
K937-22 Control Cable Extension
K937-45 Control Cable Extension
K844-1 Water Valve
WIRE FEED WELDING
• LN-25 • LN-7
• LN-23P • LN-8
• NA-3 • Spool Gun & K488 Module
• LN-742 (requires optional K1597-1 42vac trans-
former kit).
HIGH FREQUENCY GENERATORS FOR
TIG APPLICATIONS
The K799 Hi-Freq Unit and the K930-ALL TIG Modules
are suitable for use with the Commander 300. The
Commander is equipped with the required R.F. bypass
circuitry for the connection of high frequency generat-
ing equipment. The high frequency bypass network
supplied with the K799 Hi-Freq Unit does NOT need
to be installed into the Commander.
The Commander and any high frequency generating
equipment must be properly grounded. See the K799
Hi-Freq Unit and the K930-All TIG Module operating
manuals for complete instructions on installation, oper-
ation, and maintenance.
COMMANDER 300