Lucent Technologies Multiplexer and Transport System ADM 16/1 - Manual (Page 8)

This document is for planning purposes
only, and is not intended to modify or
supplement any Lucent Technologies
specifications or warranties relating to
these products or services.
Performance figures and data quoted in
this document are typical and must be
specifically confirmed in writing by
Lucent Technologies before they become
applicable to any particular order or
contract. The company reserves the right
to make alterations or amendments to
the detailed specifications at its discretion.
The publication of information in this
document does not imply freedom from
patent or other protective rights of
Lucent Technologies or others.
WaveStar is a trademark of Lucent
Technologies Inc.
To learn more about our comprehensive
portfolio and the new WaveStar™ ONG
Series, please contact your Lucent
Technologies Sales Representative
or call +33 49 23 83 333 Visit our web
site at http://www.lucent-optical.com
Copyright © 1999 Lucent Technologies.
All Rights Reserved.
Printed in Holland
Lucent Technologies Inc.
Marketing Communications
Order Number: PB-025/991102
Timing and Synchronization
Built-in oscillator Standard Accuracy 4.6 ppm acc.G.813 option 1
Built-in oscillator Stratum-3 Accuracy 4.6 ppm acc.G813 option 1,
Stability 0.37 ppm/ first 24 hours
Timing modes:
Free running mode Accuracy 4.6 ppm
Hold-over mode
Locked mode with reference to- one of the external sync. inputs
- one of the 2 Mbps tributary inputs
- one of the STM-N inputs
Automatic reference signal switching Compliant with ETSI ETS 300 417-6
Support of Synchronization Status Message on STM-N interfaces, 2 Mbps and at
2048 kbps external clock interface
Retiming on 2 Mbps
Network Management
Fully manageable by ITM-NM and ITM-SC
Local Workstation (ITM-CIT) via RJ-45
connections V.10(RS-232 compatible) / F-interface
Access to Embedded Communication Channels
via in-station Q-LAN interface G.773-CLNS1 / 10-Base-T and
10-Base-2 Interfaces
ITM-CIT for small network management CIT-Q connector / V.10
Physical design
Subrack dimensions 750 x 500 x 545 mm (H x W x D)
In accordance with ETSI
Recommendation
ETS 300 119-4 for wide racks
Rack Types 2000 mm Earthquake proof (zone 4)
2200 mm ETSI (D700) rack
2600 mm ETSI (D700) rack
Connectors-Optical Standard universal build-out optical
connector (FC/PC, SC) on the STM-4
and STM-16 interfaces
LC connectors on STM-0 and LC or SC
connectors on STM-1 interfaces
Connectors-Electrical Choice out of: SUB-D, DIN Coax, APT
Coax, Modular Jack, BT43, ISC 1.5/5.6
Connectors-Ethernet RJ-45
Station power input (Battery) -48 or -60 V DC (Range: -40,5. .. -72 V
DC)
Power Consumption 310 Watt for an average configuration
Environmental conditions
Acc. ETSI Requirement Class 3.1 Environment: 3.1 extended (3.1E)
Temperature range Humidity
Normal operation +5°C to + 45°C up to 90%
Short term operation 0°C to + 50°C up to 80%*
Storage- 25°C to + 55°C up to 100%
*Short term conditions last at most 72 hours per year during at most 15 days
EMC
EC Declaration of Conformity per ETS300 386-1 & -2: "EMC requirements for Public
Telecommunication Network Equipment" which covers:
Radiated emission EN 55022
Conducted emission EN 55022
Electro-static discharge IEC 801-2,3,4,
Radiated immunity IEC 1000-4-x series
Conducted immunity:
- Electrical fast transients IEC 1000-4-x series
- Surges IEC 1000-4-x series
- Continuous wave IEC 1000-4-x series
Compliant with LVD EN 60950
ADM161_PB025.qxd 11/10/2000 3:17 PM Page 8