Little Wonder LB800 - Manual (Page 6)

4.
D. Engine/ Fuel Warnings - "Do’s"
1. HANDLE GASOLINE WITH CARE. IT IS
HIGHLY FLAMMABLE. Refuel before starting
work.
2. Always use fresh gasoline. Stale gasoline can cause
leakage.
3. Always pull starter cord slowly until resistance is
felt. Then pull cord rapidly to avoid kick-back and
prevent arm or hand injury.
4. Replace gasoline cap securely. If fuel is spilled
move blower and fuel container from area and do
not create a source of ignition.
5. Avoid spilling fuel or oil. Always wipe unit dry
before using. Move at least 10 feet away from the
fueling point before starting engine.
6. Always store gasoline in an approved container. Fill
tank outdoors with extreme care.
C. Engine/ Fuel Warnings - "Don’ts"
1. Do not smoke while handling fuel.
2. Do not refuel a hot or running engine.
3. Do not fill tank indoors.
4. CAUTION — Do not start or run engine indoors as
poisonous carbon monoxide is emitted.
5. Do not operate in unventilated area.
6. Do not use the blower when electric system causes
spark outside the cylinder. Check spark plug from
time to time. When checking, keep plug a safe
distance from cylinder to avoid burning of
evaporated fuel from cylinder.
WARNING DANGER
HANDLE FUEL WITH CARE, IT IS HIGHLY
FLAMMABLE. FUELING A HOT ENGINE
OR NEAR AN IGNITION SOURCE CAN CAUSE FIRE
AND RESULT IN SERIOUS PERSONAL INJURY
AND/OR PROPERTY DAMAGE.
*NOTE : Numbers in brackets (#) represent Key Numbers
shown on Parts List, and parts explosion. See pages 6-8.
1. Install lower handles (30) on top of deck (32, 33). Secure
with four cap screws 5/16-18 x 1 3/4 (34), four 5/16 flat
silver washers (31), and four 5/16-18 nylon nuts (2), finger
tight.
2. Install upper handle (17) with four cap screws 5/16-18 x
1 3/4 (34), eight 5/16 washers (31), and four 5/16-18 nylon
nuts (2), finger tight. Tighten lower handle nuts and bolts.
Tighten upper handle nuts and bolts until the lower handle
tubing pinches the upper handle. It will be normal for the
lower handle tubing to crush slightly.
3. Attach throttle cable to upper handle with 1/4-20 x 1 3/4"
cap screw (19) and 1/4-20 lock nut (22) through hole on
upper handle (17). For Briggs and Stratton INTEK series
engines, the throttle control will mount on the right hand
side. For Honda engines, it will mount on the left. Insert
the 10-32 x 3/4" self-tapping screw through the hole of the
throttle control and into the pilot hole in the handle and
tighten. (NOTE: Over tightening the screw on the left hand
mounted controls could cause damage to the control.)
Once the 10-32 screw is tightened, go back to the 1/4-20
screw and tighten it enough to get a smooth action in the
control. If the throttle does not maintain it’s setting once
you start the engine, tighten this screw some more.
Connect throttle clip (15) to upper handle.
4. Tilt blower back on handle and install front wheel bracket
(51) over the three studs on lower front of blower housing.
Secure with three 5/16-18 flange nuts (5).
5. Insert pneumatic wheel sleeve (53) in front pneumatic
wheel (52). Install pneumatic wheel spacers (54) over the
axle sleeve on both sides of wheel and install in front
wheel bracket (51). Insert 3/8-16 x 5 1/4 axle bolt (50)
through wheel bracket and axle sleeve. Secure with 3/8-16
axle nut (49).
Blower Assembly Instructions
WARNING DANGER
ALL LITTLE WONDER BLOWERS ARE SHIPPED
WITHOUT OIL. WHEN FILLING OIL - USE SAE 30
OIL. REFER TO ENGINE MANUFACTURES
INSTRUCTION MANUAL FOR PROPER ENGINE
OPERATION INSTRUCTIONS.