LG 26LH1DC5 - Manual (Page 59)

59
COMMER
CIAL MODE
005 - CHAN LOCK (Channel Lock)
CHAN LOCK is ideal if the system must always be on
the same channel. Changing channels with Channel
Up/Down or keypad numbers is impossible. Channel Lock
is inactive if set to 0 (default).
Generally, this feature is used in connection with START
CHANNEL (Installer item 004) where the start channel
may, for example, be set to 3 or 4. If the start channel is 3,
then the 26LH1DC3/4/5 will remain locked on Channel 3.
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial
volume level setting when the 26LH1DC3/4/5 is turned
On. This feature is useful for an in-house information
channel, since the 26LH1DC3/4/5 would always select
that volume level when it is turned On. The range of
values are 0 - 63, 255. If 255 is selected, the current
volume level will be retained in memory when the
26LH1DC3/4/5 is turned Off; at turn On, the volume
level will be
automatically set at the previous or last level.
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level
allowable with the VOLUME (VOL) Up/Down control. In
this way, for example, someone cannot set the volume
too low to hear. The value range is from 0 to 63 —
change values with ADJ Left/Right arrow. The factory
default is 0, which provides the full range of volume
control, if item 009 MAX VOLUME is also set to 63. It
may be best to set the
same value on every 26LH1DC3/4/5.
*Note: The minimum volume level cannot have a value setting higher
than the MAX VOLUME level (described below).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level
allowable with the VOLUME (VOL) Up/Down controls. In
this way, for example, someone can not set the volume
level high enough to disturb others.
(Continued on next page)
*Note: For Items 007, 008 and 009
For legacy reasons, the scale used is 0 - 63. The PTC software
will translate this to the 0 - 100 scale used by the TV.
To translate a TV volume level to the installer menu value, use
the following formula:
Installer Value = TV Value x 63
100
Enter only the whole number (disregard fractions).
Detailed Descriptions of Installer Menu Items
000 - INSTALLER SEQUENCE
Specifies entry sequence to the Installer Menu.
0 = 9876 1 = 4321
2 = 1478 3 = 3698
001 - POWER MANAGE (Power Management)
Determines hours of no activity before automatic
shutoff. The POWER MANAGE function is for saving
energy. If set to 0, Power Manage is Off. Settings range
from 0 - 7, with 1 - 7 representing the hours that the
TV will remain On, unless there has been activity from
either the control panel or remote control.
002 - AC ON (AC Power Switchable)
If set to 1, allows the 26LH1DC3/4/5 to turn On just
by applying AC power. Pressing the On button is not
necessary. This is desirable if the 26LH1DC3/4/5 is
plugged into a cable box or a power outlet controlled by
a wall switch. Use ADJ Left/Right arrow to choose 0 or
1 where 0 is the default is Off, and 1 is On.
*Note: f set to 1 (On), the 26LH1DC3/4/5 does not respond to
On/Off commands from either the remote or the display control
panel, and the SLEEP TIMER is also nonfunctional.
003 - BAND/AFC (Band/Automatic Frequency
Control)
Selects the tuning band. There are 4 possible settings
for this option:
0 = Broadcast 1 = CATV
2 = HRC 3 = IRC
If some channels were not found by Auto Program, select
the appropriate Band setting here and add the channels
using the Channel List option in the Channel Menu.
004 - STRT CHANNEL (Start Channel)
If active, this function allows you to determine the initial
channel number when the 26LH1DC3/4/5 is turned
On. This feature is useful for an in-house information
channel, since the 26LH1DC3/4/5 would always select
that channel when it is turned On. Setting this to 255
causes the last channel viewed when the
26LH1DC3/4/5 was turned Off, to be the tuned to
channel when the 26LH1DC3/4/5 is turned On again.
255 = Last channel 1-125 = Ch X 0 = Aux
126 = Map to Channel3. 127 = Map to Channel 4.
*Note: Item 004 STRT CHANNEL cannot be set to 0 if item 093
RJP AVAILABLE is set to “1”.
INSTALLER MENU