Learning Resources RIGHT TIMER LER 6955 - Manual (Page 5)

PERSONAL PROGRAM SET
The Right Timer™ has a feature that allows you to set and save your own personal programmed
amount of time. This is very convenient for setting a standard time for a reoccurring task or test.
Once you set and save a setting for this feature, you will see this amount of time displayed every
time you enter the TIMER mode. Then all you have to do is press the START key to begin timing!
1. To your save your personal time, press the MODE button until TIMER mode is selected.
2. Press and hold the PROG button for three (3) seconds. The word TIMER will begin flashing on
the screen.
3. Use the arrow buttons to enter the desired amount of time beginning with the "seconds" section.
Press the SET button to lock in your entry. Repeat these steps with the minute and hour
sections.
4. If the amount of time you wish to enter is in whole minutes (no hours or seconds) you can use
the QUICK SET buttons to enter the total amount and press the SET button three (3) times to
lock in the entry.
5. Once you have saved your own setting, this will become the default time each time you enter
the TIMER mode. You can change this amount at any time by repeating the steps above.
6. Press the START button once to activate the timer when the timer mode is displayed on screen.
The screen will show TIMER COUNT UP or TIMER COUNT DOWN to indicate the direction of
the count!
When the timer is in COUNT UP mode, the bars on the graphic display will fill in as time passes.
When the timer is in COUNT DOWN mode, the bars will disappear as time passes.
Press the REV button to change the direction of the count. So your unit can count either up or
down. The choice is yours!
PAUSING THE TIMER
Press the FREEZE button to pause in mid-count. The display will flash "!", indicating the pause.
8 9
QUICK SET FOR WHOLE MINUTES
1. Press the MODE button until TIMER is showing on the display.
2. Press and hold the SET button for three (3) seconds to enter the programming mode. The
TIMER mode will flash on the screen indicating that you can program your time.
3. Use the 1, 5 and 10 minute buttons to "quick set" your time. For example, if you want to set
for 38 minutes, you would:
–press the 10 button three times (the screen shows 30 min)
–press the 5 button once (the screen shows 35 min)
– the 1 button three times (the screen now has total of 38 minutes).
4. Press the SET button three (3) times to accept and lock in your entry.
5. Press the START button to begin timing!
Press the REV button to change the direction of the count. So your unit can count
either up or down. The choice is yours!
SETTING TIMER USING SECONDS, MINUTES and HOURS
The procedure for setting the TIMER begins with SECONDS, then MINUTES, then HOURS.
1. To enter the timer mode from any other mode, press the MODE button until TIMER is shown
on the display screen.
2. Press and hold the SET button for three (3) seconds to enter the programming mode. The
word TIMER and the "seconds" will begin flashing, indicating you are now in the programming
mode. The first time you set the timer, the screen will show 30 minutes. This is the default
setting. Once you set your own personal setting for the PROG button (see Personal Program
Setting), that number will become the default time.
SETTING THE TIMER (SECONDS)
1. The display will flash the TIMER indicator. The display will now flash "seconds". As before,
press and hold either arrow button to advance to the "seconds" of time you want. Remember
that holding down an arrow button will advance the numbers more quickly!
2. Press the SET key to accept and confirm the seconds.
SETTING THE TIMER (MINUTES)
1. After setting the hours, the display will now flash "minutes". As before, press and hold either
arrow button to advance to the "minute" of time you want. Remember that holding down an
arrow button will advance the numbers more quickly!
2. Press the SET button to accept and confirm the minute.
SETTING THE TIMER (HOURS)
1. The "hours" place will begin flashing. Press and hold either arrow button to advance to the
"hour" of time you want. Holding down an arrow button will advance the numbers more quickly!
2. Press the SET button to accept and confirm the hour.
BARS DISAPPEAR BARS APPEAR
FLASHES WHEN
TIME IS PAUSED
6955 GUD V2 3/19/07 9:47 AM Page 5