Panasonic TC-26LX60L - Manual (Page 14)

26 27
F
AQs, etc.
T
echnical
Information
Technical Information
Closed Caption (CC)
Aspect Ratio
Let you choose the aspect depending on the format of the received signal and your preference. (p. 10) (e.g.: in case
of 4:3 image)
•
The closed caption is not displayed when you use HDMI connection.
•
If analog connected equipment is used for displaying or recording, closed caption (CC) should be set On/Off on the
connected equipment.
The CC mode setting of the TV will not affect the analog input.
If CC is set to On on both the connected equipment and the TV, captions from each unit will overlap.
•
FULL
•
JUST
FULL JUST
Enlarges the 4:3 image horizontally to the screen’s side edges.
(Recommended for anamorphic picture) Stretches to justify the 4:3 image to the four corners of the
screen.
(Recommended for normal TV broadcast)
•
H-FILL
•
4:3
H-FILL
Enlarges the 4:3 image horizontally to the screen’s side edges.
The side edges of the image are cut off. Standard
(Note that “after image” of the side bar may occur from
displaying it for a long time.)
•
ZOOM
ZOOM
Enlarges the 4:3 image to the entire screen.
(Recommended for Letter Box)
•
Zoom adjust
Vertical image position and size can be adjusted in “ZOOM.”
Select “Zoom adjust” on the “Picture” menu. (p. 12-13)
V-Position: Vertical position adjustment Size: Vertical size adjustment
Side bar
•
To reset the aspect ratio (OK)
HDMI connection
HDMI (high-definition multimedia interface) allows you to enjoy high-definition digital images and high-quality sound by connecting
the TV unit and the equipment.
HDMI-compatible equipment (*1) with an HDMI or DVI output terminal, such as a set-top box or a DVD player, can be connected
to the HDMI connector using an HDMI compliant (fully wired) cable.
•
HDMI is the world’s first complete digital consumer AV interface complying with a non-compression standard.
•
If the external equipment has only a DVI output, connect to the HDMI terminal via a DVI to HDMI adapter cable (*2).
•
When the DVI to HDMI adapter cable is used, connect the audio cable to the audio input terminal. •
Audio settings can be made on the “HDMI in” menu screen. (p. 12-13)
Applicable audio signal sampling frequencies (L.PCM): 48 kHz, 44.1 kHz, 32 kHz
(*1): The HDMI logo is displayed on an HDMI-compliant equipment.
(*2): Enquire at your local digital equipment retailer shop.
Caution
•
Use with a PC is not assumed.
•
All signals are reformatted before being displayed on the screen.
•
If the connected equipment has an aspect adjustment function, set the aspect ratio to “16:9”. •
This HDMI connector is “type A”.
•
Equipment having no digital output terminal may be connected to the input terminal of either “COMPONENT”, “S-VIDEO”, or
“VIDEO” to receive analog signals.
•
The HDMI input terminal can be used with only the following image signals: 480i, 480p, 720p and 1080i
Match the output setting of the digital equipment.
•
For details of the applicable HDMI signals, see below.
horizontal
frequency (kHz)
vertical
frequency (Hz) COMPONENT HDMI
525 (480) / 60i 15.73 59.94 * *
525 (480) /60p 31.47 59.94 * *
750 (720) /60p 45.00 59.94 * *
1,125 (1,080) /60i 33.75 59.94 * *
* Mark: Applicable input signal for Component (Y, P B , P R ) and HDMI
•
Signals other than those shown above may not be displayed properly.
•
The above signals are reformatted for optimal viewing on your display.
Input signals that can be displayed
Note
Control with HDMI “HDAVI Control™”
HDMI connections to some Panasonic equipment allow you to enjoy easy playback.
•
Set up the equipment to enable this function. Read the manual for the equipment.
• Switch the TV unit on again with the equipment on when connection or setup is changed.
•
This function may not work normally depending on the equipment condition.
•
The equipment can be operated by TV’s remote control with this function on even if TV is in Standby mode.
•
Image or sound may not be available for the first few seconds when the playback starts.
•
Image or sound may not be available for the first few seconds when Input mode is switched.
Note
•
480i (4:3), 480i (16:9), 480p (4:3), 480p (16:9) : FULL, JUST,
4:3 or ZOOM
•
1080i / 720p : FULL, H-FILL, JUST or 4:3
• When the signal is 720p/1080i, the aspect mode automatically
defaults to Full after turning off the TV, after changing
input mode, or after changed signal resolution other than
720p/1080i.
Pic. mode
•
Vivid (default) : Provides enhanced picture contrast and sharpness for viewing in a well-lit room. •
Standard : Recommended for normal viewing conditions with subdued room lighting.
•
Cinema : For watching movies in a darkened room. It provides a soft, film-like picture.