Panasonic SB-ZT2 - Manual (Page 2)

VQT2T88
2
Setup example Front speaker
(right)
Front speaker
(left)
Connected equipment
Main unit Surround
speaker
(left)
Surround
speaker (right)
Approx.120°
Supplied accessories/AC power supply connection/Control guide/Installation
• Aim the front face (with Panasonic logo) of each speaker at the
listening-viewing position for setting.
• Place the surround speakers slightly at the back right and left of the
listening-viewing position.
As this system uses a frequency band of 2.4 GHz, the radio waves
may be interrupted by an obstacle. Depending on the surrounding
environment (i.e. radio wave interruption from outside, etc.) or the
building structure where this system is used (i.e. wall that easily
reflects radio waves, etc.), sounds may be cut or noise may occur.
Install this system properly paying attention to the following descriptions.
„
Equipment certification
As this system received Technical Conditions compliance certifi cation
based on the Radio Law, the wireless station license is not required.
However, if you do the following actions to this system, you may be
held accountable by law.
• Disassemble or refurbish
„ Restrictions for use
• Domestic use only.
• Use this system in the same room.
„
Do not place an obstacle between the main unit (SC-ZT2) and
speakers.
Radio waves from this system reach a maximum range of 15 m
(49 feet) in the same room. If there is an obstacle between the main
unit (SC-ZT2) and speakers or the main unit (SC-ZT2) is placed at
the height of 50 cm (1.6 feet) or below from the floor, the radio waves
reach a smaller range.
„
Keep this system away from equipment that generates radio
wave interference.
If the following equipment is located near the system, install this
system away from such equipment.
• Bluetooth, OA devices, telephone, etc.: approx. 3 m (10 feet) or
more
• Microwave oven, wireless LAN compatible devices: approx. 3 m
(10 feet) or more
This system is designed to automatically avoid radio wave interference
with such household equipment. If radio wave interference occurs, the
Wireless Link display ( ➜ page 14 of SC-ZT2 Operating Instructions) may
blink, the sounds from speakers may be interrupted or noise may occur.
These phenomena occur when this system selects a proper
frequency. These are not malfunctions.
„
Keep this system away from metal objects that tend to reflect
radio waves.
If there are metal objects or furniture in the room where this system is
installed, radio waves tend to be reflected. Depending on the listening-
viewing position, sounds may be interrupted or noise may occur. These
symptoms may be remedied by slightly moving this system’s position.
Note that radio waves tend to be reflected also when this system is
installed in rooms with a lot of activity.
„ There is no positional distinction for each speaker before setting.
„ Make sure to place the speakers on a flat, stable surface so
there is no danger of them falling over.
„ When carrying speakers, hold the pole and base parts. (➜ left)
„ The speakers of this system are not magnetically shielded. Do
not install this system near a CRT-based television.
Note
• Make sure the base parts are not covered by cloth such as a curtain.
• Before attaching the leg cushion (included) on the base parts to
prevent tilt or rattle on the floor, make sure there are no people in
the surrounding area.
• Set the distance from each speaker to the listening-viewing position.
( ➜ page 22 of SC-ZT2 Operating Instructions)
Installation
Wireless functions
Please check and identify the supplied accessories.
Use numbers indicated in parentheses when asking
for replacement parts.
(Product numbers correct as of January 2010. These
may be subject to change.)
Only for U.S.A. and Puerto Rico: To order accessories, refer
to “Accessory Purchases
(United States and Puerto
Rico)” on page 5.
Only for Canada: To order accessories, call the dealer from
whom you have made your purchase.
Supplied accessories
2 AC power supply cords
(K2CB2CB00021)
Leg cushions (1 sheet: 8 pieces) (RFA3045-2)
Keep the leg cushion out of reach of children to prevent swallowing.
AC IN
To save power when the system is not to be used for a long time,
unplug it from the household AC outlet.
Make sure to turn this system off before unplugging the AC power
supply cord.
For power consumption of speakers in Standby, see right page.
AC power supply connection
Household AC outlet
(AC 120 V, 60 Hz)
AC power supply
cord (included)
The included AC power supply cords are for use with this system only.
Do not use them with other equipment. Also, do not use AC power
supply cord for other equipment with this system.
Note
Side view
Control guide
TEST terminal
ID switch
AC IN TEST ID
2
1
Speaker (with built-in amplifier)
TEST terminal: This is used to check the product
operation status. Only used in factory. Do not
insert a foreign object.
ID switch: This is used to check the product
operation status and not used regularly.
WIRELESS LINK
Pole (mid-high part)
Base
(woofer
part)
Side view
AC inlet (➜ above)
1 [WIRELESS LINK] indicator (➜ right
page)
2 For switching the speaker “ON/OFF”
( ➜ right page)
Note
POWER
5$<622
8366 A'PAKPFF 5$<622
8366 A'PAKPFF