Pioneer Elite VSX-90TXV - Manual (Page 56)

Other Settings 09
56
En
Assigning the HDMI inputs
• Default settings:
HDMI - 1 – DVD/LD
HDMI - 2 – TV/SAT
You only need to change this setting when you didn’t
connect your HDMI component according to the default
settings for the HDMI input terminals (see above). By
specifying the type of the connected component and to
which input terminal it is connected, video signals can be
delivered properly when you select an HDMI component
as the input source.
1
Select ‘HDMI Input’ from the Input Assign menu.
2 Select the number of the HDMI input to which
you’ve connected your video component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
3 Select the component that corresponds with the
one you connected to that input.
Select between
DVD/LD, TV/SAT, DVR 1, DVR 2 or OFF.
• Use
/ and ENTER to do this.
• To hear audio from your HDMI component (through
this system), you must also make separate audio
connections to the corresponding inputs on the rear
of the receiver. For more on this, see
Using SIRIUS
Radio on page 46.
• If you connect any video component to the receiver
using HDMI, you should also have your TV connected
to this receiver’s HDMI output.
4 When you're finished, press RETURN.
You return to the Input Assign menu.
The Other Setup menu
The Other Setup menu is where you can make
customized settings to reflect how you are using the
receiver.
1 Press RECEIVER on the remote control, then press
the SETUP button.
An on-screen display (OSD) appears on your TV. Use
/
// and ENTER to navigate through the screens
and select menu items. Press
RETURN to confirm and
exit the current menu.
2 Select ‘Other Setup’ then press ENTER.
3 Select the setting you want to adjust.
If you are doing this for the first time, you may want to
adjust these settings in order:
• DRC Setup – Specify the amount of dynamic range
adjustment to Dolby Digital or DTS soundtracks (see
Dynamic Range Control Setup below).
• Dual Mono Setup – Isolate one channel when
listening to discs with dual mono encoding (see
Dual
Mono Setup below).
• LFE ATT Setup – Choose the attenuator level for the
LFE channel (
LFE Attenuator Setup on page 57).
• SR+ Setup – Specify how you want to control your
Pioneer plasma display (
SR+ Setup for Pioneer
plasma displays on page 57).
• Video Conv. Setup – Specify if you want analog
video signals converted for output to your TV (
Video
Converter Setup on page 57).
• Multi Zone Setup – Specify your volume setting for
a MULTI-ZONE setup (see
Multi Zone Setup on
page 58).
• 12V Trigger Setup – Specify which components you
want to switch on or off using the 12 volt trigger (see
12 Volt Trigger setup on page 58).
4 Make the adjustments necessary for each setting,
pressing RETURN to confirm after each screen.
Dynamic Range Control Setup
• Default setting: OFF
This setting specifies the amount of dynamic range
adjustment to Dolby Digital and DTS movie soundtracks.
You may want to use this when listening to surround
sound at low volumes.
1 Select ‘DRC Setup’ from the Other Setup menu.
2 Choose the setting that you want.
• OFF – No dynamic range adjustment (use when
listening at higher volume).
• MID – Mid setting.
5. Input Assign
:Return
a.Digital Input
b.Component Input
c.HDMI Input
5c.HDMI Input
:Finish
HDMI - 1 DVD/LD
HDMI - 2 [ TV/SAT ]
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
: Exit
6.Other Setup
:Return
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR+ Setup
e.Video Conv. Setup
f. Multi Zone Setup
g.12V Trigger Setup
6.Other Setup
:Return
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR+ Setup
e.Video Conv. Setup
f. Multi Zone Setup
g.12V Trigger Setup
DRC OFF
6a.Dynamic Range Control
:Finish
VSX-90TXV_KU.book Page 56 Friday, March 16, 2007 5:46 PM