Patton electronic ONSITE 2800 User Manual
Onsite 2800 series managed vpn router, User manual
Advertising
OnSite 2800 Series
Managed VPN Router
User Manual
Sales Office:
+1 (301) 975-1000
Technical Support:
+1 (301) 975-1007
E-mail:
WWW:
Part Number: 07M2800-GS, Rev. F
Revised: February 22, 2012
Important
This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial
or residential environment.
Advertising
Table of contents
Document Outline
- Summary Table of Contents
- Table of Contents
- List of Figures
- List of Tables
- About this guide
- Chapter 1 General information
- Chapter 2 Hardware installation
- Chapter 3 Getting started with the OnSite Managed VPN Router
- Chapter 4 Serial port configuration
- Introduction
- Serial port configuration task list
- Disabling an interface
- Enabling an interface
- Configuring the encapsulation for Frame Relay
- Enter Frame Relay mode
- Configuring the LMI type
- Configuring the keep-alive interval
- Entering Frame Relay PVC configuration mode
- Configuring the PVC encapsulation type
- Binding the Frame Relay PVC to IP interface
- Enabling a Frame Relay PVC
- Disabling a Frame Relay PVC
- Displaying serial port information
- Displaying Frame Relay information
- Integrated service access
- Chapter 5 T1/E1 port configuration
- Introduction
- T1/E1 port configuration task list
- Enable/Disable T1/E1 port
- Configuring T1/E1 port-type
- Configuring T1/E1 clock-mode
- Configuring T1/E1 line-code
- Configuring T1/E1 framing
- Configuring T1/E1 line-build-out (T1 only)
- Configuring T1/E1 used-connector (E1 only)
- Configuring T1/E1 application mode
- Configuring T1/E1 LOS threshold
- Configuring T1/E1 encapsulation
- Create a Channel-Group
- Configuring Channel-Group Timeslots
- Configuring Channel-Group Encapsulation
- Entering HDLC Configuration Mode
- Configuring HDLC CRC-Type
- Configuring HDLC Encapsulation
- T1/E1 Configuration Examples
- Chapter 6 VPN configuration
- Chapter 7 Access control list configuration
- Introduction
- About access control lists
- Access control list configuration task list
- Mapping out the goals of the access control list
- Creating an access control list profile and enter configuration mode
- Adding a filter rule to the current access control list profile
- Adding an ICMP filter rule to the current access control list profile
- Adding a TCP, UDP or SCTP filter rule to the current access control list profile
- Binding and unbinding an access control list profile to an IP interface
- Displaying an access control list profile
- Debugging an access control list profile
- Examples
- Chapter 8 Link scheduler configuration
- Introduction
- Configuring access control lists
- Configuring quality of service (QoS)
- Quick references
- Link scheduler configuration task list
- Defining the access control list profile
- Creating a service policy profile
- Specifying the handling of traffic-classes
- Defining fair queuing weight
- Defining the bit-rate
- Defining absolute priority
- Defining the maximum queue length
- Specifying the type-of-service (TOS) field
- Specifying the precedence field
- Specifying differentiated services codepoint (DSCP) marking
- Specifying layer 2 marking
- Defining random early detection
- Discarding Excess Load
- Devoting the service policy profile to an interface
- Displaying link arbitration status
- Displaying link scheduling profile information
- Enable statistics gathering
- Chapter 9 LEDs status and monitoring
- Chapter 10 Contacting Patton for assistance
- Appendix A Compliance information
- Appendix B Specifications
- Appendix C Cabling
- Appendix D Port pin-outs
- Appendix E OnSite 2800 Series factory configuration
- Appendix F Installation checklist