Panasonic SC-VK960 - Manual (Page 31)

31
RQTV0239
LANG - 5
LANG - 4
FRANÇAIS
DANSK
ENGLISH
OTHER OPERA
TIONS
Using the timers
Setting the time Setting the time
This is a 24-hour clock.
1 Press [CLOCK / TIMER] to select “CLOCK”.
Every time you press the button:
CLOCK ˚ PLAY
Original display
˚ REC
2 ( Within 7 seconds or so )
Press [
4, / REW] or [¢, / FF] to set the
time.
3 Press [CLOCK / TIMER] to finish setting the time.
Displaying the time
Press [CLOCK / TIMER] once when the unit is on or in
standby mode.
The time is displayed for a few seconds.
Note:
Reset the clock regularly to maintain accuracy.
Using the play or record timer Using the play or record timer
You can set the timer to come on at a certain time to
wake you up (play timer) or to record from the radio or
the external equipment (record timer).
Play timer and record timer cannot be used together.
Turn the unit on and set the clock.
• For the play timer, prepare the desired music
source; cassette (DECK 2 has the priority), disc
number (1 ~ 5), radio or external equipment, and set
the volume.
• For the record timer, check the cassette’s erasure
prevention tabs ( \ page 27) and insert the tape in
DECK 2 (
\
page 27) and tune to the radio station
( \ page 26) or select the external equipment
( \ page 32).
1 Press [CLOCK/TIMER] to select the timer function.
Every time you press the button:
CLOCK
˚ PLAY
Original display
˚ REC
˚PLAY : to set the play timer
˚REC : to set the record timer
(Proceed to the next step
within 7 seconds )
2 ( Within 7 seconds or so )
Press [ 4, / REW] or [¢, / FF] to set the
“ON” time.
3 Press [CLOCK / TIMER] to confirm.
4 Repeat steps 2 to 3 to set the “OFF” time.
To activate the timer
5 Press [
˚PLAY/REC] to display the timer’s
indicator.
Every time you press the button:
˚ PLAY
(off)
˚ REC
˚PLAY : to turn the play time on
˚REC : to turn the record timer on
(The indicator does not appear if the start and fi nish
times or the clock has not been set.)
6 Press [ y] to turn off the unit.
The unit must be off for the timers to operate.
To change the settings
Perform steps 1 to 4 and 6 (
\
see above).
To change the source or volume
When the unit is on
1 Press [ ˚PLAY/REC] to clear the timer indicator
from the display.
2 Make changes to the source or volume.
3 Perform steps 5 and 6 (
\
see above).
To adjust speaker level during play To adjust speaker level during play
Effective when playing multi-channel audio or when
Dolby Pro Logic
II or Super Surround is turned on.
1 Press [CH SELECT] to select the speaker.
L C R RS LS SW
SW: Subwoofer
• You can adjust SW only if the disc includes a
subwoofer channel.
• “SW” does not appear on the display and is not
adjustable when Dolby Pro Logic II is turned on.
• “S” appears on the display when “MUSIC”
or “MOVIE” is selected with Super Surround
(
\ page 30). In this case, you can adjust both
surround speaker levels at the same time using
[
5, ∞].
S : –6 dB to +6 dB
2 Press [ 5] (increase) or [∞] (decrease) to adjust
the speaker level for each speaker.
C, RS, LS, SW: –6 dB to +6 dB
(L, R: Only the balance is adjustable.)
To adjust the balance of the front speakers
While “L” or “R” is selected, press [
2, 3].
Using the timers (continued)
RQTV0239_1L.indd 31 RQTV0239_1L.indd 31 6/12/07 12:36:44 PM 6/12/07 12:36:44 PM