Panasonic SC-ZT2 - Manual (Page 15)

VQT2R70
15
Setting surround speakers
„
Link the front speakers wirelessly fi rst and then make the settings for the surround speakers.
Preparations
• Make sure that all equipment has been turned off.
(When the VIERA Link “HDAVI Control” compatible Panasonic TV (VIERA) and Blu-ray Disc player/DVD recorder (DIGA) are
connected, do not turn on the TV (VIERA) and Blu-ray Disc player/DVD recorder (DIGA) until the setting is complete.)
• Connect AC power supply of main unit and 4 speakers to household main sockets. (➜ page 12)
• Make sure that the main unit and speakers have been turned off.
• Prepare the remote control. (➜ page 7)
1. Turn the main unit on.
2. Turn on the front speakers.
• The color of the [WIRELESS LINK] indicator of the front speaker changes from red to green.
• Do not turn on the surround speakers yet at this point. The color of the [WIRELESS LINK] indicator does not change from red to green even if the power is turned on.
3. Set “4CH ” at the setting operation of “Changing the number of speakers to 4” below.
4. Turn the main unit off once.
5. Turn the main unit on again.
• “ 4CH SEARCH ” appears on the display. (This is displayed only at the fi rst-time setting.)
6. Turn on the surround speakers.
• The color of the [WIRELESS LINK] indicator of the surround speaker changes from red to green.
• When the [WIRELESS LINK] indicator of each speaker lights green, “ 4CH SEARCH ” display disappears.
7. Press and hold [CH] on the remote control for about 3 seconds until “4 SPKR SET ” is
displayed on the main unit’s display.
• Always aim the remote control at the main unit for operation.
8. Press the remote control button corresponding to the speaker outputting the confi rmation sound.
When the sound is output
from the surround speaker
(right), press [ RETURN].
When the sound is
output from the surround
speaker (left), press
[–SETUP, OFF].
When the sound is
output from the front
speaker (left),
press [GAME]. When the sound is output
from the front speaker
(right), press [MUTE].
Front speaker
(left) Front speaker
(right)
Surround
speaker (left) Surround
speaker (right)
GAME MUTE
RETURN
–SETUP,
OFF
• Sound is output from any of the speakers.
• When you press the button corresponding to the confi rmation sound of a speaker, another speaker outputs the confi rmation
sound. Press the corresponding button in the same way and complete settings for all 4 speakers.
• When “ COMPLETE ” disappears from the main unit’s display, the speaker setting is complete.
Note
• Check if the speakers are properly set after setting the speakers. ( ➜ page 14)
• If the speakers are set incorrectly in step 8, turn the main unit off then on again and perform steps 7 and 8.
• If the [WIRELESS LINK] indicator does not change from red to green, see page 27 of “Troubleshooting guide”.
Speaker setting
Connection
Changing the number of speakers to 4
1. Press and hold [–SETUP, OFF] for about 2 seconds.
The setting items are displayed. ( ➜ page 21)
2. Press [w][q] to select “SPEAKERS ” and press [OK].
3. Press [e][r] to select “4CH ” and press [OK].
2CH : When only front speakers are installed (factory setting)
4CH : When surround speakers are additionally installed
• When changing the number of speakers to 2, select “
2CH ” and press [OK].
4. Press [e][r] to select “YES ” and press [OK].
• To cancel, select “ NO ”.
5. Press [ RETURN] several times to select “EXIT ” and press [OK]
to fi nish the setting.
Note
When you select “ EXIT ” and press [OK] in step 2, the setting mode fi nishes.
„ To return to the previous
display/To cancel during
setting operation: Press
[ RETURN].
5%<622
8364 'PKPFF 5%<622
8364 'PKPFF ඦ೨   ඦ೨