Panasonic PT-AE500U - Manual (Page 21)

E NGLISH -41
Adjustments
and
settings
40-E NGLISH
Adjusting the position
Press the F or G button to select
an item, and then press the I or H
button to change the setting.
For items with bar scales, press the
ENTER button or the I or H button
to display the adjustment screen,
and then Press the I or H button
to make the adjustment.
When an S-VIDEO/VIDEO/DVI
signal is being input.
B When a DVI signal is being input,
only “ASPECT” can be adjusted.
When a YP B P R signal is being input
When a PC signal is being input
P O S I T I O N
H - P O S I T I O N 0
V - P O S I T I O N 0
A S P E C T 1 6 : 9
S E L E C T E N T E R E S C
Horizontal position
(H-POSITION)
(S-VIDEO/VIDEO/YP B P R /PC only)
To move the picture to the left: I button
To move the picture to the right: H button
Vertical position
(V-POSITION)
(S-VIDEO/VIDEO/YP B P R /PC only)
To move the picture down: I button
To move the picture up:
H button
DOT CLOCK
(PC only)
Periodic striped pattern interference
(noise) may occur when a striped
pattern such as the one below is
projected. If this happens, press the
I or H button to adjust so that any
such noise is minimised.
CLOCK PHASE
(PC/YP B P R only)
Adjust the “DOT CLOCK” setting
first before carrying out this
adjustment. Press the I or H
button to adjust so that the noise
level is least noticeable.
P O S I T I O N
H - P O S I T I O N 0
V - P O S I T I O N 0
D O T C L O C K 0
C L O C K P H A S E 0
A S P E C T 4 : 3
A U T O S E T U P
S E L E C T E N T E R E S C
When the input signal is from a
PC, first select “AUTO SETUP”
and then press the ENTER button
to initiate automatic positioning.
If the optimum setting is not
obtained when “AUTO SETUP” is
carried out, adjust by the following
procedure.
P O S I T I O N
H - P O S I T I O N 0
V - P O S I T I O N 0
C L O C K P H A S E 0
A S P E C T 4 : 3
S E L E C T E N T E R E S C
ASPECT
Refer to page 28.
AUTO SETUP
(PC only)
“H-POSITION”, “V-POSITION”,
“DOT CLOCK” and “CLOCK
PHASE” are automatically adjusted
according to the input signal.
Changing the display language
Indicates the language which is
currently set
# Select “LANGUAGE” from the “MAIN MENU” and then press the
ENTER button.
$ Press the F or G button to select a language and then press the
ENTER button.
L A N G U A G E E N G L I S H
E N G L I S H
D E U T S C H
F R A N Ç A I S
E S P A Ñ O L
I T A L I A N O
S E L E C T E N T E R E S C
Turning off the picture momentarily
(SHUTTER)
The “SHUTTER” function can be used to momentarily turn off the picture
when the projector is not being used for short periods of time. The projector
uses less power in “SHUTTER” mode than it does in normal projection
mode.
# Select “SHUTTER” from the “MAIN MENU” and then press the
ENTER button.
$ Press any button on either the projector or remote control unit
(except the LIGHT button) to return to normal operating mode.
B When YP B P R signals are being
input, “CLOCK PHASE” can be
adjusted only when HDTV60/
HDTV50/750p signals are
being input.
NOTE:
B When the “ASPECT” is set to
“V SCROLL” (page 28), “AUTO
SETUP” cannot be performed.
NOTE:
B If signals with a dot clock
frequency of 100 MHz or higher
are being input, interference
may not be completely
eliminated when the “DOT
CLOCK” and “CLOCK PHASE”
adjustments are carried out.