PYLE Audio PLCD19XMR - Manual (Page 12)

“FREQ/CLOCK/NO PRI priority” mode.
And then you can press VOL button (11)
or VOL button (12) to select frequency
priority or clock priority or no priority.
- When select Frequency Priority:
The frequency will appear on the unit
all the while. Pressing DISP button (1)
while in Frequency Priority will temporarily
display clock and then returns to
frequency display.
- When select Clock Priority:
The clock will appear on the unit all the
while. Pressing DISP button (1) while in
Clock Priority will temporarily display
selected station frequency (in RADIO
mode) or track number (in CD/CDC
mode) and then returns to clock display.
- When select No Priority:
When the frequency appears on the unit,
pressing DISP button (1) will display
clock and it will not return to frequency
display until DISP button (1) pressed
again. When the clock appears on the
unit, pressing DISP button (1) will display
frequency information.
12hours/24hours
Hold press SEL/MENU button (10) for
several seconds, when BEEP ON/OFF
appears, press SEL/MENU button (10)
shortly five times to select
“12hours/24hours” mode. And then you
can press VOL button (11) or VOL
button (12) to set 24 hours mode or 12
hours mode.
- When the currently displayed function
has not been adjusted for several
seconds, it will exit menu set mode.
- When you have set CLOCK ON during
power off state, LCD backlight will be
turn on together.
DISPLAY INFORMATION
When pressed quickly, the DISP button
(1) changes the display as follows.
- In AM/FM mode:
-> Frequency ->CLOCK ->
- In XM mode:
-> Channel Name -> Artist Name ->
Song Title -> Category Name -> CLOCK
->
- In CD mode:
-> CD ->CLOCK ->
- In CDC (or AUX) mode:
->CDC (or AUX)->CLOCK ->
Each display time is 5 seconds, the display
will return to the first position after 5
seconds.
12
OPERATION
SET THE CLOCK
Press the DISP button (1) shortly until the
clock is shown on the LCD display. Then
hold down DISP button (1) until the clock
flashes. Then press the CH button (17)
clockwise to change hours or rotate the
CH button (16) to change minutes.
MUTE
In radio/XM/AUX IN mode, press
/MUTE button (3) to mute audio level.
Press the button again to release mute
function.
LOUDNESS
Press LOUD (DIM) button (15) shortly to
reinforce the bass output and display will
show “LOUD”. Press it again to release
this function.
MODE SELECTION
Press MODE button (6) to sequence through
primary operating modes in the following
order: radio >XM > CD> CDC> AUX.
If playback media (CD) is not loaded into
mechanism, CD mode will be skipped. If
CDC is not connected to head unit, CDC
mode will be skipped.
If XM receiver connector is disconnected
to XM head unit, XM mode will be skipped.
LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated
functions on the display (8).
ILLUMINATION
Press LOUD (DIM) button (15) for more
than 2 seconds to adjust the brightness
of the LCD display backlight.
RESET FUNCTION
Reset button (25) must be activated with
either a ballpoint pen or thin metal object.
The reset button is to be activated for the
following reasons:
- Initial installation of the unit when all
wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
Note: If press reset button (25), the unit
can’t work yet, please use a cotton swab
soaked in isopropyl alcohol to clean the
socket on the front panel.
RECOVERING INITIAL VALUE
In radio (AM/FM) mode, press MODE
button (6) for more than three seconds,
the display will appear “EEP INIT”, and all
settings recover factory value.