Panasonic WV-CP464 - Manual (Page 2)

1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light Control (ELC)
(2) The SUPER-D2 function eliminates interference by strong background lighting
which makes the camera picture dark, such as a spotlight.
Dynamic range of 46 dB.
(3) Various External Sync Functions, including Gen-Lock
(4) Auto/Manual White Balance Function
(5) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB
3. Minimum illumination of 0.8 lx (0.08 footcandle) with F 1.4 lenses.
4. Minimum illumination of 0.4 lx (0.04 footcandle) with Panasonic aspherical high speed
(F0.75) lenses.
5. 480 lines of horizontal resolution
FEATURES
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
q Auto Iris Lens Connector
This connector is used to connect the auto iris lens with a 4-pin male connector sup-
plied as a standard accessory (Part No. YFE4191J100).
w Focus Fixing Screw
e Flange-back Adjusting Ring
This ring is used to adjust the back focal length or picture focus. Rotate this ring clock-
wise for a C-mount lens or counterclockwise for a CS-mount lens.
r Lens (Option)
t Camera Mounting Screw Hole
This hole is used to mount the camera onto a mounting bracket.
<WV-CP460>
<WV-CP464>
q e w r
t
y
o
u !0
!1 i
!2
!3
!2
!5
!3
!4
Super Dynamic
WV-
CP460
Hi-Z G/L 75 Ω
VIDEO OUT
120V AC 60Hz
GEN-LOCK
AC 24V
IN
DC 12V
IN
1
2
VIDEO OUT
GND
GEN-LOCK
LOCK
Slide the panel to the left until it locks.
CONNECTIONS
A. WV-CP460 (120 V AC 60 Hz)
1. Plug the AC power cord (supplied as standard accessory) into the AC Inlet Socket.
2. Connect the AC power cord to a 120V AC 60 Hz outlet.
Notes:
• Connect the power cord firmly.
• The power cord should be long enough for panning and tilting.
If the cable is too short, the power cord plug may be pulled off the camera when the
camera pans or tilts.
B. WV-CP464 (12 V DC/24 V AC)
The WV-CP464 has an AC/DC compatible input terminal. The 12 V DC or 24 V AC power
supply cord can be connected to this terminal. The camera detects the power source auto-
matically.
AC 24V
IN
DC 12V
IN
1
2
GND
12 V DC
(10.8 V - 16 V)
Copper wire #24 #22 #20 #18
size (AWG) (0.22mm 2 ) (0.33mm 2 ) (0.52mm 2 ) (0.83mm 2 )
Resistance 0.078 0.050 0.030 0.018
Ω
/m
Resistance 0.026 0.017 0.010 0.006
Ω
/ft
Resistance of copper wire [at 20°C (68°F)]
• Calculation of maximum cable length between camera and power supply
10.8 V DC
≤
V
A
- (R x 0.42 x L)
≤
16 V DC
L : Cable length (m)
R : Resistance of copper wire (
Ω
/m)
V
A
: DC output voltage of power supply
unit
V
A
−
12
L standard = (m)
0.42 x R
V
A
−
16
L minimum = (m)
0.42 x R
V
A
−
10.5
L maximum = (m)
0.42 x R
1. 12 V DC Power Supply
Connect the power cord to the AC/DC compatible input terminal on the rear panel of the
camera.