Panasonic DMR E50 - Manual (Page 9)

9
The remote control (continued)
Television operation
You can control televisions by changing the remote control code.
Preparation
≥ Turn on the television.
≥ Switch [DVD, TV] (15) to “TV”.
1 Refer to the chart below for the code for your
television.
2 Press and hold [TV, Í ] (14) and enter the two-digit
code with the numeric buttons (4) .
≥ For example: 01, press [0] ) [1].
≥ After entering the code, test the remote control by turning on
the television and changing channels.
Note
≥ If there is more than one code, repeat the procedure until you find
the code that allows correct operation.
≥ Repeat this procedure after you change the batteries.
≥ If your television brand is not listed or if the code listed for your
television does not allow control of your television, this remote is
not compatible with your television.
List of TVs Compatible with the unit’s Remote Control
Brand: Code
Panasonic 01, 02, 03, 04, 44
AIWA 35
AKAI 27, 30
BLAUPUNKT 09
BRANDT 10, 15
BUSH 05, 06
CURTIS 31
DESMET 05, 31, 33
DUAL 05, 06
ELEMIS 31
FERGUSON 10
GOLDSTAR/LG 31
GOODMANS 05, 06, 31
GRUNDIG 09
HITACHI 22, 23, 31, 40, 41, 42
INNO HIT 34
IRRADIO 30
ITT 25
JVC 17, 39
LOEWE 07
METZ 28, 31
MITSUBISHI 06, 19, 20
MIVAR 24
NEC 36
NOKIA 25, 26, 27
NORDMENDE 10
ORION 37
PHILIPS 05, 06
PHONOLA 31, 33
PIONEER 38
PYE 05, 06
RADIOLA 05, 06
SABA 10
SALORA 26
SAMSUNG 31, 32, 43
SANSUI 05, 31, 33
SANYO 21
SBR 06
SCHNEIDER 05, 06, 29, 30, 31
SELECO 06, 25
SHARP 18
SIEMENS 09
SINUDYNE 05, 06, 33
SONY 08
TELEFUNKEN 10, 11, 12, 13, 14
THOMSON 10, 15
TOSHIBA 16
WHITE WESTINGHOUSE 05, 06
Operation: Button
On and off: [TV, Í ] (14)
Video input mode: [AV] (3)
Channels: [ W , X , CH] (18)
Volume: [ i , j , VOLUME] (19)
Numeric: [0-9, -/--] (4)
ª The 3 methods for switching to the AV input on your
Panasonic TV
Your Panasonic TV uses one of 3 different methods for switching
between TV reception and the AV input(s). Perform the operations
steps listed for the switching methods A, B and C below to
determine which one your Panasonic TV uses.
A
1) Switch [DVD, TV]
(15) to “TV”.
2) Press [AV] (3) to switch to the AV input.
Each press of [AV] (3) switches between “TV reception” and
“AV input(s)”.
B (for the remote control code No.44)
1) Switch [DVD, TV]
(15) to “TV”.
2) Press [AV] (3) .
Colour bars for selecting the AV input appear on the TV
screen.
3) Follow the instructions displayed on the TV screen to select
the desired AV input from the displayed colour bars for the AV
input by pressing [A]
(29) , [B] (28) , [C] (33) or [D] (34) on the
remote control.
C (for the remote control code No.01)
1) Switch [DVD, TV]
(15) to “TV”.
2) Press [AV] (3) .
The last previously selected AV input indication appears on the
TV screen. The indications for selecting another AV input also
appear, but they disappear a few seconds later.
3) Before the indications for selecting another AV input
disappear, press [A] (29) , [B] (28) , [C] (33) or [D] (34) to
select the desired AV input.
With the following four buttons, you can move and select as
follows:
[A]
(29) : Move left
[B] (28) : Move down
[C] (33) : Move up
[D] (34) : Move right
SONY08
TELEFUNKEN10ÅE4
THOMSON10, 15
TOSHIBA16
WHITE WESTINGHOU