Pioneer DV-S88A - Manual (Page 11)

11
En
Rear Panel
1
COMPONENT VIDEO OUT switch
You only need to set this switch if you’re using an
NTSC TV/monitor connected via the component
video outputs of this player. This player can output
NTSC video as a standard interlaced signal (the
525i(480i) setting), or as a non-interlaced, or
progressive scan signal (the 525p(480p) setting).
If your TV/monitor is compatible with progressive
scan video, set this switch to either 525p(480p) or
MENU SELECT. When set to MENU SELECT, you
can use the on-screen Setup menu to switch
between progressive and interlaced video output.
If your TV/monitor is not progressive scan
compatible, you will not be able to see any picture if
this player is set to output progressive scan video. In
this case, set the switch to 525i(480i) to restore the
picture (page 37).
2
COMPONENT VIDEO OUT jacks
(Interlace/Progressive-scan)
If your TV or monitor has component video inputs,
you can produce a higher quality picture on your TV
or monitor by connecting to the component video
outputs on this unit (page 18).
3
D2 jack
(Interlace/Progressive-scan)
If your TV or monitor has D video input, you can
produce a higher quality picture on your TV or
monitor by connecting to the D2 video output on this
unit (page 18).
4
S-VIDEO OUT jacks
If your TV or monitor has an S-video input, clear
picture reproduction is possible by connecting the
player to your TV or monitor via the S-Video jack
(page 18).
You can switch between [S1] and [S2] S-video
output from the Setup menu (page 38).
5
VIDEO OUT jacks
Connect to the video input on a TV or monitor or AV
amplifier or receiver with video input capability.
(pages 14, 18).
6
AC IN power cord connection terminal
Use to connect the power cord to the wall outlet
(pages 14, 15).
7
CONTROL IN/OUT jacks
Use to connect this player to another component
bearing the Pioneer
Î mark. This lets you control
this unit as though it were a component in a system.
Player operations are then performed by pointing the
remote control at the component that the player is
connected to (page 19).
8
DIGITAL OUT jack (optical (OPT))
Use to output the digital audio signal recorded on
discs. You can output the digital signal via either
optical output jack to an AV amplifier or receiver
(page 16).
9
DIGITAL OUT jack (coaxial (COAX))
Use to output the digital audio signal recorded on
discs. You can output the digital signal via either
coaxial output jack to an AV amplifier or receiver
(page 16).
0
TV SYSTEM switch* (DV-S838A only)
Use to change the TV signal mode to either PAL or
NTSC according to the type of TV and disc to be
used. When the switch is in the AUTO position, the
player outputs the format on the disc as is (page 19).
-
AUDIO OUT FRONT jacks
Use to output two-channel audio (analog) to the
audio stereo inputs on a TV or stereo amplifier. If you
are connecting to a receiver that has both digital and
analog input jacks for DVD player connection, it may
be beneficial to make both connections (pages 14,
17).
=
AUDIO OUT (5.1 channel) jacks
Use to output 6 discrete audio channels of decoded
digital audio to a receiver or amplifier with discrete
audio inputs (pages 15, 17).
R L
Y P B P R
525i
(480i)
525p
(480p)
MENU
SELECT
COAX OPT
AC IN
AUDIO OUT
FRONT REAR
LS
RS
CENTER
SUB
WOOFER
VIDEO OUT S-VIDEO OUT
CONTROL DIGITAL OUT
IN OUT
COMPONENT VIDEO OUT
1
1 2 1 2
2
1
2
AUTO
NTSC
PAL
TV SYSTEM
D2
1 2 4 5 3 6
7 8 0 9 - =
NAMES AND FUNCTIONS
Illustration is DV-S838A
*