Phoenix Gold pm700 - Manual (Page 7)

Power Output: (20 Hz to 20kHz, with
no more than 0.1%)
325 watts per channel
into 8 ohms
475 watts per channel
into 4 ohms
Bridged Mono:
950 watts into 8 ohms
at 1kHz, with no more
than 0.1% THD
Dynamic Headroom: >2.0 dB
Frequency Response:
20Hz to 20kHz
(±0.75dB)
Channel Separation:
>65 dB @ 1kHz
Damping Factor: <400
Input Impedance: 25 Kohms unbalanced
50 Kohms balanced
Sensitivity: High: 0.775V RMS for
rated power into 4
ohms 72mV
RMS for 1W
into 4 ohms
Low: 1.5 V
RMS for rated
power into 4 ohms
140mV
RMS for 1W into
4 ohms
Gain: High: 35.0dB (±0.5 dB)
Low: 29.0dB (±0.5 dB)
Input Overload: +18 dBu
THD: < 0.1%
IM Distortion: < 0.1%
Signal-to-Noise Ratio:
>100dB, A-weighted,
ref. to rated power into
4 ohms
Slew Rate: 40V / µS (Band
width limited)
CMRR: >80dB @ 1kHz
Power Consumption:
90W at idle; 725W with
musical program;
1370W at full power
into 8 ohms (continu-
ous); 2000W at full
power into 4 ohms
(continuous)
Power Requirements:
120VAC / 60Hz (USA
and Canada) Other
voltages as required for
export
Fusing: 12 amp slo-blo
(120V / 60Hz) 8 amp
slo-blo (230V / 50Hz)
Sequence Receive Terminal:
+7V to +15VDC 50mA
min. current require-
ment
Display: 7 LED indicators per
channel, 1 green
READY, 5 yellow SIG-
NAL, 1 red CLIP/ PRO-
TECT
Size (H x W x D): 3.50” (2U) x 19” x
13.25” 89
mm x 483 mm
x 337 mm
Net Weight: 34 lbs. (15.4 kgs)
Shipping Weight: 36 lbs. (16.36 kgs)
Due to ongoing product development,
features, specifications, and availability are
subject to change without notice.
5
pm950
• 325W per channel into 8 ohms
475W per channel into 4 ohms
950W mono into 8 ohms
• XLR and 1/4” TRS input connectors
• Accepts balanced or unbalanced lines
• Multi-way Binding Post output connectors
• Independent 11 detent Level Controls for CH1
and CH2
• External Level Control Defeat Switch
• Dual Mono mode for operating both channels
with
a single mono input
• Bridged Mono mode for combining the power of
both channels into a single higher powered chan-
nel
• Input sensitivity set at 1.5V RMS from factory.
Internally reconfigurable to 0.7775V RMS .
• Internally configurable input polarity
• Internal connection points for add-on accessories
• Power ON Sequencer
• Class H dual-rail power supply
• Independent CH1 / CH2 Speaker relays will
instantaneously disconnect if one of the following
fault conditions is detected:
D.C. Offset
Over Temperature
Short Circuit
• Additional protection circuitry includes:
Clipping Eliminator
AC Line Fuse
• Power Connected / Standby indicator
• 7 LED display per channel, including Power
Ready and Clip / Protect indicators
• 2-speed Fan cooled
• 70 volt / 100 volt transformer option
• CE 1997 approved
4
BACK