Polk Audio SR65006 - Manual (Page 3)

F O R M O R E I N F O R M AT I O N V I S I T O U R W E B S I T E AT W W W. P O L K A U D I O . C O M
3
S A F E L I M I T S
O F O P E R AT I O N
Your Polk Audio loudspeakers are made with
the highest quality materials for years of
trouble-free performance. However, damage
to loudspeakers can occur when an amplifier,
regardless of its wattage, is made to play at
higher listening levels than its power can
cleanly produce (usually beyond the “1 to 2
o’clock” position on the volume control).
This results in very high levels of audible dis-
tortion, originating in the amplifier, which
adds a harsh, gritty sound to the music.
Contrary to popular belief, a speaker is more
likely to be damaged by trying to get too
much volume from a low-powered amplifier
than from a high-powered one.
F O R T E C H N I C A L
A S S I S TA N C E O R
S E R V I C E
Call Polk Audio’s Customer Service
Department at 1-800-377-7655 from 9am to
6pm, Eastern Time, Monday through Friday,
or e-mail us at [email protected].
Please do not hesitate to call us if you
have questions about your speaker system.
Visit http://www.polkaudio.com/car
S R 6 5 0 0 S P E C S
Continuous Power Handling
125 Watts
Peak Power Handling
250 Watts
Impedance (Nominal)
4 Ohms
Frequency Response (+/-3dB)
40 Hz - 30 kHz
Sensitivity (1W/1m)
90 dB
Driver Mounting Diameter
5 5/8" (142.9 mm)
Driver Mounting Depth
2 9/16" (64.9 mm)
Tweeter Flush Cup
Mounting Diameter
2" (50.8 mm)
Tweeter Angle Mount Cup
Mounting Diameter
1 3/4" (44.5 mm)
Tweeter Flush Cup
Mounting Depth
1" (25.4 mm)
Tweeter Angle Mount Cup
Mounting Depth
5/8" (15.87 mm)
Grille Height
1 1/8" (28.7 mm)
Grille Diameter
6 15/16" (176.2 mm)
Crossover Frequency
3100 Hz
Driver Crossover Slope
(Low Pass)
2nd Order, 12 dB/Octave
Tweeter Crossover Slope
(High Pass)
3rd Order, 18 dB/Octave
Tweeter Attenuation
Level Settings
+1 dB, 0 dB, -1.5 dB, -3 dB
T H I E L E / S M A L L
PA R A M E T E R S
S R 6 5 0 0 D R I V E R
Fs
60 Hz
Re
3.5 Ohms
Z
4 Ohms
Qms
10.3
Qes
0.7
Qts
0.65
Le
0.38 mH
Vas (Cubic Feet & Liters)
0.4 Cu. Ft., 11.3 L
Cms
440 um/N
BL
5.6 T-m
Sd (sq. in. & sq. cm.)
21 sq. in., 135 sq. cm.
Xmax Linear (in. & mm.)
0.16", 4mm Peak
(Double for Peak to Peak)
Xmax—Mechanical (in. & mm.)
0.32", 8.1mm Peak
(Double for Peak to Peak)
Voice Coil Diameter (in. & mm.)
1.5", 38.1mm
S R 5 2 5 0 S P E C S
Continuous Power Handling
100 Watts
Peak Power Handling
200 Watts
Impedance (Nominal)
4 Ohms
Frequency Response (+/-3dB)
60 Hz - 30 kHz
Sensitivity (1W/1m)
90 dB
Driver Mounting Diameter
4 3/4" (120.6 mm)
Driver Mounting Depth
2 1/4" (56.41mm)
Tweeter Flush Cup
Mounting Diameter
2" (50.8 mm)
Tweeter Angle Mount Cup
Mounting Diameter
1 3/4" (44.5 mm)
Tweeter Flush Cup
Mounting Depth
1" (25.4 mm)
Tweeter Angle Mount Cup
Mounting Depth
5/8" (15.87 mm)
Grille Height
1 1/8" (28.7 mm)
Grille Diameter
6 3/16" (157 mm)
Crossover Frequency
4600 Hz
Driver Crossover Slope
(Low Pass)
2nd Order, 12 dB/Octave
Tweeter Crossover Slope
(High Pass)
3rd Order, 18 dB/Octave
Tweeter Attenuation
Level Settings
+2 dB, 0 dB, -1.5 dB, -3 dB
T H I E L E / S M A L L
PA R A M E T E R S
S R 5 2 5 0 D R I V E R
Fs
71 Hz
Re
3.6 Ohms
Z
4 Ohms
Qms
8.28
Qes
0.78
Qts
0.72
Le
0.25 mH
Vas (Cubic Feet & Liters)
0.2073 Cu. Ft., 5.87 L
Cms
490 um/N
BL
4.6 T-m
Sd (sq. in. & sq. cm.)
14.33 sq. in., 92.46 sq. cm.
Xmax Linear (in. & mm.)
0.1", 2.5 mm Peak
(Double for Peak to Peak)
Xmax—Mechanical (in. & mm.)
0.362", 9.2 mm Peak
(Double for Peak to Peak)
Voice Coil Diameter (in. & mm.)
1", 25.4 mm