Pioneer Elite VSX-23TXH - Manual (Page 103)

Additional information 12
103
En
Remote control
HDMI
During playback of a Surround
EX or DTS-ES source on the
SBch AUTO setting, EX or ES
does not appear, or the signal
is not properly processed. • The source may be Dolby Surround EX/DTS-ES software, but it has no flag to indicate it is 6.1
compatible. Set to SBch ON (see Using surround back channel processing on page 59), then switch
to the THX Surround EX or Standard EX listening mode (see Listening in surround sound on page 56).
During playback of DVD-Audio,
the display shows PCM. • This will occur when playing DVD-Audio material over the HDMI connection. This is not a
malfunction.
The power turns off
automatically and some
indicator flashes, or some
indicator flashes and the power
does not turn on. • See the Power section (page 98).
Symptom Remedy
Cannot be remote controlled. • Set a 5-digit preset code corresponding to the receiver to be operated in the remote control (see
Operating multiple receivers on page 73).
• Check whether the receiver’s remote control mode is properly set (see Remote Control Mode Setup
on page 96).
• Try replacing the batteries in the remote control (see Loading the batteries on page 9).
• Be sure to operate within 7 m (23 ft.) and a 30º angle of the remote sensor on the front panel (see
Operating range of remote control unit on page 9).
• Check that there are no obstacles between the receiver and the remote control.
• Make sure that there is no fluorescent or other strong light shining on to the remote sensor.
• Check the connections of the CONTROL IN jack (see Operating other Pioneer components with this
unit’s sensor on page 35).
Other components can’t be
operated with the system
remote. • If the battery ran down, the preset codes may have been cleared. Re-enter the preset codes.
• The preset code may be incorrect. Redo the procedure for entering preset codes.
Symptom Remedy
The HDMI indicator blinks
continuously. • Check all the points below.
No picture or sound. • This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-
compatible. If they are not, please connect them using the component, S-Video or composite video
jacks.
• Depending on the connected source component, it’s possible that it will not work with this receiver
(even if it is HDCP-compatible). In this case, connect using the component, S-Video or composite
video jacks between source and receiver.
• If the problem still persists when connecting your HDMI component directly to your monitor,
please consult the component or monitor manual or contact the manufacturer for support.
• If video images do not appear on your TV or flat panel TV, try adjusting the resolution, Deep Color
or other setting for your component.
• While analog video signals are being output over HDMI, use a separate connection for audio
output.
• When this receiver reproduces MULTI CH IN audio sources with the HDMI setting set to
THROUGH, you cannot hear audio output from all channels. In this case, make a digital or analog
audio connection.
• To output signals in Deep Color, use an HDMI cable (High Speed HDMI™ Cable) to connect this
receiver to a component or TV with the Deep Color feature.
No picture. • Try changing the Resolution setting (in Setting the Video options on page 68).
• VSX-23TXH only: Set the HDMI output setting to the connected HDMI OUT terminal (in Switching
the HDMI output on page 71).
No sound, or sound suddenly
ceases. • Check that the HDMI AV setting is set to AMP/THROUGH.
• If the component is a DVI device, use a separate connection for the audio.
• If analog video is being output over HDMI, please use a separate connection for the audio.
• Check the audio output settings of the source component.
Symptom Remedy
VSX-23TXH_CUXJ.book 103 ページ ２００９年５月８日 金曜日 午前１０時４５分