Initial settings, 02 operating this unit, Using an aux source – Pioneer DEH-5300UB User Manual

Page 7: Turning the clock display on or off

Advertising
background image

The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the cut-off frequency

and output level of the subwoofer.
Cut-off frequency (Cut-off frequency display
flashes.)

—Output level (Output level display

flashes.)

3 Turn M.C. to select the desired setting.

Cut-off frequency:

50HZ

—63HZ—80HZ—100HZ

—125HZ
Output level:

-24 to +6

SLA (source level adjustment)

SLA (Source Level Adjustment) lets you adjust the vo-
lume level of each source to prevent radical changes
in volume when switching between sources.
! Settings are based on the FM volume level, which

remains unchanged.

! The AM volume level can also be adjusted with

this function.

! When selecting FM as the source, you cannot

switch to

SLA.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range:

+4 to

–4

3 Press M.C. to confirm the selection.

Initial Settings

1

Press and hold S (SRC/OFF) until the

unit turns off.

2

Press M.C. and hold until function name

appears in the display.

3

Turn M.C. to select the initial setting.

After selecting, perform the following proce-
dures to set the initial setting.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock dis-

play you wish to set.
Hour

—Minute

3 Turn M.C. to adjust the clock.

AUX (auxiliary input)

Activate this setting when using an auxiliary device
connected to this unit.
1 Press M.C. to turn AUX on or off.

USB (plug and play)

This setting allows you to switch your source to

USB/

iPod automatically.
1 Press M.C. to turn the plug and play function on

or off.
ON

– When a USB storage device/iPod is con-

nected, depending on the type of device, the
source is automatically switched to

USB/iPod

when you turn on the engine. If you disconnect
your USB storage device/iPod, this unit

’s source

is turned off.
OFF

– When a USB storage device/iPod is con-

nected, the source is not switched to

USB/iPod

automatically. Please change the source to

USB/

iPod manually.

ILLUMI (illumination color select)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

RED (red)

—GREEN (green)

3 Press M.C. to confirm the selection.

SW CONTROL (rear output and subwoofer setting)

The rear speaker leads output and RCA output can be
used for full-range speaker or subwoofer connection.
If you switch to

REAR-SP :SW, you can connect a rear

speaker lead directly to a subwoofer without using an
auxiliary amp.
Initially,

REAR-SP is set for rear full-range speaker

connection (

FUL).

1 Press M.C. to display the setting mode.

2 Turn M.C. to change the output and press to se-

lect.
REAR-SP

—PREOUT

3 Turn M.C. to change the setting.

REAR-SP: FUL

—SW

PREOUT: SW

—REA

! Even if you change this setting, there will be

no output unless you turn the subwoofer out-
put on (refer to

SUBWOOFER1 (subwoofer on/

off setting) on the previous page).

! If you change this setting, subwoofer output

in the audio menu will return to the factory
settings.

DEMO (demo display setting)

1 Press M.C. to turn the demo display on or off.

En

12

Section

02

Operating this unit

SCROLL (scroll mode setting)

When ever scroll is set to ON, recorded text informa-
tion scrolls continuously in the display. Set to OFF if
you prefer the information to scroll just once.
1 Press M.C. to turn the ever scroll on or off.

Using an AUX source

1

Insert the stereo mini plug into the

AUX input jack.

2

Press S (SRC/OFF) to select AUX as the

source.

Note

AUX cannot be selected unless the auxiliary set-
ting is turned on. For more details, refer to

AUX

(auxiliary input) on the previous page.

Turning the clock display
on or off

% Press

to turn the clock display on or

off.
# The clock display disappears temporarily
when you perform other operations, but the clock
display appears again after 25 seconds.

En

13

English

Section

02

Operating this unit

<QRD3066-A/N> 7

Advertising