Panasonic CQ-CB9900U - Manual (Page 17)

32
CQ-CB9900U CQ-CB9900U
33
(page 34)
Audio Settings
1
Press [VOLUME]
(PUSH SEL: select).
Volume
Default: 18 Setting range: 0 to 40
Bass/Treble
You can adjust the bass and treble sound.
Default: BAS (bass) 0 dB TRE (treble) 0 dB
Setting range:
j12 dB to i12 dB (by 2 dB)
SQ Adjustment
You can adjust the characteristics of the currently
selected sound type (SQ).
It is also possible for a maximum of 5 different
adjusted SQ to be preset.
Adjustable frequency:
60 Hz, 160 Hz, 400 Hz, 1 kHz, 3 kHz, 6 kHz, 16 kHz
Setting range:
j12 dB to i12 dB (by 2 dB)
≥ Setting of SQ, bass/treble and volume are
infl uenced one another. If the infl uence
mentioned above causes distortion to the audio
signal, readjust bass/treble or volume.
∫ To return an adjusted SQ to the default
setting (page 33)
(Push)
Push
Push
Push
Push
Example: CD mode
[VOLUME "]: Up
[VOLUME #]: Down
Note:
≥ Press [DISP] (display) to return to the regular
mode.
≥ If no operation takes place for more than
5 seconds in audio setting (2 seconds in the
volume setting, 10 seconds in SQ adjustment),
the display returns to the regular mode.
≥ The volume can also be adjusted directly using
[VOLUME] on the main unit (page 11).
2
Turn [VOLUME].
Press [VOL "] or [VOL #].
[VOLUME "]: Increased
[VOLUME #]: Decreased
[VOLUME "]: Increased
[VOLUME #]: Decreased
[VOLUME "]
[VOLUME #]
6 4
9 7
5
Car Audio
SOURCE
MUTE
POWER
RAND
VOL
3 1 2
DISP BAND
REP
6 5
SET
SEL
#
SCAN
MENU
NUMBER
8
0 [DISP]
(Display)
[SEL]
(Select)
[VOL "]
[VOL #]
[ %] [$]
[ "] [#]
Adjust
1 Press [ %] or [$] to select a frequency.
[ $]: Increased
[ %]: Decreased
2 Turn [VOLUME] to adjust the equalizer level.
[VOLUME "]: Up
[VOLUME #]: Down
Memorize
3 Press and hold [ "] or [#] for more than
2 seconds to enter.
4 Press [ "] or [#] to select a preset number
(2 to 6).
5 Press and hold [ "] or [#] for more than
2 seconds to memorize.
≥ The display blinks once.
≥ The adjusted SQ is preset in the number of the
selected button, and the regular display is restored.
Press and hold one of the buttons from [2] to [6]
for more than 2 seconds.
Note:
≥ Only buttons [2] to [6] can be used to preset the
adjusted SQ. An adjusted SQ cannot be preset in
button [1].
≥ To call a preset SQ, refer to page 12.
≥ While the SQ adjustment mode is established,
only adjustments are performed, and even if the
adjustment mode is exited without presetting an
adjusted effect, what has been set will be refl ected as
the current SQ until another SQ is selected.
≥ Even when the SQ presets are adjusted, the display
which appears when the settings are called remains
unchanged.
[2] to [6]
(SQ preset
buttons)
∫ To return an adjusted SQ to the default
setting
1 Press [SQ] during regular mode, and select
the SQ which is to be returned to the default
setting.
2 Press and hold [BAND] for more than
2 seconds.
[BAND]