Radio & others, The radio, Press [fm/am] to select “fm – Panasonic SC-HT820V User Manual

Page 42: Press and hold [enter, Repeat steps 1 to 3 to set the am bands, Press [fm/am] to select “fm” or “am, Press the numbered buttons to select the channel, Press [ 6 ] or [ 5 ] to select the frequency, Tune to the station ( ➜ left), Press [enter

Advertising
background image

42

RQT7388

The radio

Press [TUNER] to put the remote control in TUNER mode.

Up to 15 stations can each be set in the FM and AM bands.

1

Press [FM/AM] to select “FM”.

2

Press [

6] or [5] to tune to the

lowest frequency (“FM 87.9” MHz or
“FM 87.5” MHz).

3

Press and hold [ENTER].

Release the button when “FM AUTO” is displayed.

The tuner presets all the stations it can receive into the
channels in ascending order.
≥“SET OK” is displayed when the stations are set. The last

station to be set is then played.

4

Repeat steps 1 to 3 to set the AM
bands.

1

Press [FM/AM] to select “FM” or “AM”.

2

Press the numbered buttons to select
the channel.

Alternatively, press [

W CH] or [X CH].

To select a 2-digit number
e.g. 12: [

S10] ➜ [1] ➜ [2].

When a stereo FM broadcast is being received.

If noise is excessive in FM

Press [PLAY MODE] to display “MONO”.

Press [PLAY MODE] again to cancel the
mode.
The mode is also canceled when you
change the frequency.

1

Press [FM/AM] to select “FM” or
“AM”.

2

Press [

6] or [5] to select the

frequency.

Press and hold [

6] or [5] until the frequency starts

scrolling to start automatic tuning. Tuning stops when a station
is found.

1

Tune to the station (

left).

2

Press [ENTER].

3

While “PGM” is flashing on the display

Press the numbered buttons to select
a channel.

Alternatively, press [

W CH] or [X CH] then press [ENTER].

The station occupying a channel is erased if another station is preset
to that channel.

FM frequency step

Main unit only
The step is factory-set to 0.2 MHz, but you can change it to receive
broadcasts allocated in 0.1-MHz steps.
1 Press [INPUT SELECTOR]

on the main unit to select “FM”.

2 Press and hold [INPUT SELECTOR].

After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.

To return to the original step, repeat the above steps.

[Note]

Any FM/AM frequencies preset in channels will be changed by this
procedure. Preset them again.

VOLUME

1

2

3

4

5

6

7

8

0

100

9

CH

NAVI

SKIP

SLOW/SEARCH

MENU

ENTER

DIRECT

NAVIGATOR

TOP MENU

RETURN

OSD/

DISPLAY

TV

FM/AM

DVD/VHS

DVD

TV

VHS

TUNER

DISC 1

DISC 2

DISC 3

DISC 4

PICTURE MODE

SETUP

OPEN/CLOSE/EJECT

JET REW

CD MODE

DISC 5

S10

ENTER

PLAY

LIST

TV VOL

TV VOL

RESET

TV/VIDEO

PAGE

GROUP

MIX 2CH

SUBTITLE

REPEAT

PLAY MODE

MULTI RE-MASTER

SUBWOOFER LEVEL

C.S.M

SFC

C.FOCUS

SUPER SRND

PROGRESSIVE

MUTING

POSITION

INPUT SELECTOR

OPEN/CLOSE

EJECT

DISC CHANGE

DISC CHECK

INPUT

SELECTOR

REC

/REW

FF/

STOP

PLAY

DOWN

UP

PHONES

CH

VOLUME

STOP

-DEMO

DISC

D I S C

1

2

3

4

5

1

2

3

4

5

PLAY

POWER

Í

/I

INPUT SELECTOR

Automatic presetting

Selecting the preset channels

ST

TUNED

MONO

Manual tuning

Presetting the channel one by one

PGM

7388en.book 42 ページ 2003年12月22日 月曜日 午後9時39分

Advertising