Panasonic SL-SX240 - Manual (Page 5)

5
Using the Unit with Optional Accessories
Using the unit with an audio system
Using a stereo phono cable (not included), you can lis-
ten to CDs on your audio system.
≥ Turn off this unit and the other equipment before con-
nection.
≥ Do not connect the cable to the PHONO jacks on the
amplifier.
≥ Obtain the optional connecting cable if the other
equipment comes with mini-phone jacks.
≥ Set the unit’s volume to 10, then adjust the volume
level on the other equipment.
≥ You can connect speakers, active or otherwise, with
an impedance of 1 k
≠ or less to the headphone jack.
Using the unit with a car audio
system
Items to be purchased
For connection to the car audio system:
Car stereo cassette adaptor (SH-CDM10A)
Connect the car stereo cassette adaptor to the
unit’s headphone jack.
(When doing this, set this unit's volume to 10.)
For securing the unit and connecting the power
supply:
≥ Car adaptor (SH-CDC9)
≥ Car mounting kit (SH-CDF20)
Note when using the car mounting kit (SH-CDF20)
Note 1
≥ When you switch off the car, volume and sound quality
may return to the original settings and the resume
function may work even if you change the disc.
≥ It may not be possible to use the unit with some types
of car stereos owing to restrictions imposed by the
construction of the car stereo cassette adaptor.
For further details, refer to the instructions of the part
concerned.
L
R
Maintenance
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
If the surfaces are extremely dirty, use a soft cloth
dipped in a soap-and-water solution or a weak deter-
gent solution.
≥ Never use alcohol, paint thinner or benzine to clean
this unit.
≥ Before using chemically treated cloth, read the instruc-
tions that came with the cloth carefully.
Maintaining the lens
Open the lid and clean the lens as shown in the figure.
Use a cotton swab to gently wipe off any finger-prints.
Recommended product: Lens cleaner kit (SZZP1038C)
Air blower for
camera lens
Lens
Lens
Headphone jack ( Ë )
(Red)
(White)
Stereo phono cable (not included)
To CD or AUX
terminals
Other equipment
1 Remove the screw from
the bracket at the rear
of the car mounting
base.
2 Replace the screw in
the lower hole of the
bracket.
Bracket
Screwdriver
Using the Wired Remote Control
The remote control can be operated regardless of the
hold mode of the unit.
Preparation:
Release the remote control from the HOLD mode.
∫ Operation confirmation tones
When an operation button is pressed, a confirmation
tone sounds. Refer to the parentheses in the illustration
for the different types of confirmation tones.
How to use the wired remote control
To start play
To stop play
To turn off the
unit
Press once during off or stop mode.
Press once during play.
Press and hold during play or stop
mode.
Skipping
tracks
Searching
through tracks
To adjust the
volume
Press once during play.
(Press [
: ] twice to skip to the be-
ginning of the previous tracks.)
Backward
Forward
Press and hold during play.
≥ The volume range is 0–25. (Press
and hold to change the volume suc-
cessively.)
≥ A tone (beep-beep) sounds when
you reach the minimum or maximum
volume.
HOLD
VOL
(Beep...Beep)
(Beep)
(Beep...Bee...p)
(Beep Beep)
(Beep Beep
Beep)
SL-SX280
SL-SX280
Decrease
(Beep)
Increase
(Beep)