Polk Audio D5000.5 - Manual (Page 6)

10 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 11
Loose or poor audio input . Check line level connections and repair
or replace as needed .
Loose power connections . Check power wires and ground connections
and repair or replace as needed .
distorted output
Amplifier level sensitivity set
too high exceeding maximum
capability of amplifier . Readjust gain . Refer to the Adjusting the Sound
of the System section of this manual .
Impedance load to amplifier too low . Check speaker impedance load, if below (2 Ohm,
4 Ohm bridged; 1 Ohm sub) rewire the speakers
to achieve higher impedance .
Shorted speaker wires . Check speaker wires and repair or replace as needed .
Speaker not connected
to amplifier properly . Check speaker wires and repair or replace as needed .
Internal crossover not
set properly for speakers . Readjust crossovers . Refer to the Line Level
Inputs/Controls section of this manual .
Speakers are blown . Check system with known working speakers
and fix or replace as needed .
Poor bass response
Speakers wired with wrong polarity
causing cancellation at low frequencies . Check speaker polarity and fix as needed .
Crossover set incorrectly . Reset crossovers . Refer to the Line Level Inputs/Controls
section of this manual .
Impedance load at amplifier is too low . Check speaker impedance load, if below (2 Ohm,
4 Ohm bridged; 1 Ohm sub) rewire the speakers
to achieve higher impedance .
Battery fuse blowing
Short in power wire or incorrect wiring . Check power wires and ground connections
and repair or replace as needed .
Fuse used is smaller than recommended . Replace with proper fuse size .
Actual current exceeds fuse rating . Check speaker impedance load, if below (2 Ohm,
4 Ohm bridged; 1 Ohm sub) rewire the speakers
to achieve higher impedance .
Amplifier fuse blowing
Fuse used is smaller than recommended . Replace with proper fuse size .
Impedance load at amplifier is too low . Check speaker impedance load, if below (2 Ohm,
4 Ohm bridged; 1 Ohm sub) rewire the speakers
to achieve higher impedance .
Speaker is blown with shorted outputs . Check system with known working speakers
and fix or replace as needed .
Actual current exceeds fuse rating . Check speaker impedance load, if below (2 Ohm,
4 Ohm bridged; 1 Ohm sub) rewire the speakers
to achieve higher impedance .
TrOuBLESHOOTINg TIPS
Symptom Probable Cause Action To Take Amplifier PA d5000.5
Type Bridgeable
Class D MOSFET
Channels 5 channel
RMS Continuous Power
@ 4 Ohms 70 W x 4; 200 W x 1
RMS Continuous Power
@ 2 Ohms 100 W x 4; 400 W x 1
RMS Continuous Power
Bridged @ 4 Ohms 200 W x 2
RMS Continuous Power
1 Ohm (Sub) 500 W x 1
Distortion at Rated Power <0 .1%
Remote Gain Control Included Yes (sub only)
Minimum Impedance Bridged 4 Ohms
Minimum Impedance
Not Bridged 2 Ohms
Minimum Impedance
Subwoofer Channel 1 Ohm
Signal-to-noise Ratio 105dB
Frequency Response 20Hz-20kHz
Crossover Filter Slope
(dB/octave) 12dB/octave
Front Gain Control 200mV - 6V
Filter Switch (Front) 3-position
(BPF, Full, HPF)
High Pass Filter
Frequency Range (Front) 40Hz - 400Hz
Low Pass Filter
Frequency Range (Front) 80Hz - 4kHz
Amplifier PA d5000.5
Filter Switch (Rear) 2-position (Full, HPF)
High Pass Filter
Frequency Range (Rear) 40Hz - 4000Hz
Rear Gain Control 200mV - 6V
Line Level Inputs (y/n) Yes
Line Level Outputs (y/n) No
LED Power Indicator Yes
LED Protection Indicator Yes
Supply Voltage 10V - 16V
Fusing & Power/Type (2) 40 Amp ATC
Power Connections 4 AWG
Ground Connections 4 AWG
Speaker Connections 12 AWG
Height 1 13/16" (46 mm)
Depth 6 3/4" (171.5 mm)
Width 13 5/16" (338.1 mm)
Width w/ Terminal Adaptor 14 1/16" (357.9 mm)
Weight 6 .75 lbs (3 .06 kg)
SPECIFICATIONS