Pioneer VSX-LX52 - Manual (Page 64)

Using other functions 08
64
En
4 Use the MASTER VOLUME dial to adjust the
volume for the zone you have selected.
This is only possible if you selected the Variable volume
control in ZONE Audio Setup on page 89.
1
5 When you’re finished, press MULTI-ZONE
CONTROL again to return to the main zone controls.
You can also press MULTI-ZONE ON/OFF on the front
panel to switch off all output to the sub zone(s).
2
MULTI-ZONE remote controls
Set the MULTI-ZONE operation switch to ZONE 2 or ZONE
3 to operate the corresponding zone.
The following table shows the possible MULTI-ZONE
remote controls:
Making an audio or a video recording
You can make an audio or a video recording from the
built-in tuner, or from an audio or video source
connected to the receiver (such as a CD player or TV).
3
Keep in mind you can’t make a digital recording from an
analog source or vice-versa, so make sure the
components you are recording to/from are hooked up in
the same way (see Connecting your equipment on
page 14 for more on connections).
Since the video converter is not available when making
recordings (from the video OUT jacks) make sure to use
the same type of video cable for connecting your recorder
as you used to connect your video source (the one you
want to record) to this receiver. For example, you must
connect your recorder using Component video if your
source has also been connected using Component video.
For more information about video connections, see
Connecting an HDD/DVD recorder, VCR and other video
sources on page 27.
1 Select the source you want to record.
Use the input function buttons (or INPUT SELECT).
• If necessary, press , then press SIGNAL
SEL to select the input signal corresponding to the
source component (see Choosing the input signal on
page 55 for more on this).
2 Prepare the source you want to record.
Tune to the radio station, load the CD, video, DVD etc.
3 Prepare the recorder.
Insert a blank tape, MD, video etc. into the recording
device and set the recording levels.
Refer to the instructions that came with the recorder if
you are unsure how to do this. Most video recorders set
the audio recording level automatically—check the
component’s instruction manual if you’re unsure.
4 Start recording, then start playback of the source
component.
Reducing the level of an analog signal
The input attenuator lowers the input level of an analog
signal when it’s too strong. You can use this if you find
that the OVER indicator lights often or you can hear
distortion in the sound.
4
• Press , then press A.ATT to switch the
input attenuator on or off.
Note
1 The volume levels of the main and sub zones are independent.
2 • You won’t be able to switch the main zone off completely unless you’ve switched off the MULTI-ZONE control first.
• If you don’t plan to use the MULTI-ZONE feature for a while, turn off the power in both the sub and main rooms so that this receiver is in
standby.
Button What it does
 Switches on/off power in the sub zone.
INPUT SELECT Use to select the input function in the sub
zone.
Input function
buttons Use to select the input function directly (this
may not work for some functions) in the sub
zone.
MASTER
VOLUME +/– Use to set the listening volume in the sub
zone.
3 • The receiver’s volume, Audio parameters (the tone controls, for example), and surround effects have no effect on the recorded signal.
• Some digital sources are copy-protected, and can only be recorded in analog.
• Some video sources are copy-protected. These cannot be recorded.
4 The attenuator isn’t available with digital sources, or when using the Stream Direct (ANALOG DIRECT) modes.
DVD BD DVR HDMI
TV CD CD-R
TUNER INPUT SELECT
VIDEO
iPod USB
1 2 3
SLEEP
HDMI OUT
MCACC SIGNAL SEL
4 5 6
REMOTE
SETUP
ZONE 2
MAIN
ZONE 3
TV/DTV
AUDIO INFO
DISP
MPX PQLS
CH
RECEIVER TV CTRL
RECEIVER
1 2 3
SLEEP
HDMI OUT
MCACC SIGNAL SEL
4 5 6
DIMMER A.ATT SBch
7 8 9
CLASS CH LEVEL D.ACCESS
0 ENTER
REMOTE
SETUP
ZONE 2
MAIN
ZONE 3
AUDIO INFO
DISP
CH
RECEIVER TV CTRL
RECEIVER
VSX-LX52_SVYXJ.book 64 ページ ２００９年２月２６日 木曜日 午後４時３１分