PYLE Audio PICL48 User Manual
Page 3
LOCATION OF CONTROLS
1
Adjustable Dock Dial
11
Program/Memory/Alarm2 Button
2
iPod/iPhone Connector
12
Volume + Button
3
Speaker
13
Volume - Button
4
CD Compartment
14
Open CD Door Button
5
Power/Alarm Off Button
15
Remote Sensor
6 Function/Clock
Adjust
Button
16 Display
7
Play/Pause/Sync Button
17
DC In Jack
8 Skip-/Tune-
Button
18 FM
Antenna
9
Skip+/Tune+ Button
19
Aux-In Jack
10 Stop/Memory+/Alarm1
Button
- 4 -
CONNECTING THE UNIT TO POWER
Plug one end of the AC/DC adaptor into the DC-In jack, and then plug the other end into AC wall outlet.
Before switching on the unit, make sure that the voltage of your electricity supply is the same as that
indicated on the rating plate.
Backu-up Battery
Open the battery door located at the bottom of the unit, insert 2 pcs. ‘AAA’ size (UM-4) batteries with
battery polarities same as shown inside the battery compartment.
In case of AC power outage or interrupted AC power, the current time, alarm time settings and the
stored radio stations are preserved in the memory of the unit.
Important: When the unit is not use for 3 days or more and also the unit is not connect to AC power
during that time, please remove the battery to avoid damage to the set from leakage of battery.
SETTING THE TIME
Before starting to set the time, make sure that the unit is in POWER OFF Mode .
If you have iPod (Except iPod Shuffle) or iPhone
1.) Dock in the iPod/iPhone on the 30 pins Connector
2.) Press the ‘PLAY/PAUSE/SYNC’ button for a few seconds until the display will show SYNC with
flashing, then the unit will synchronize the time same as the iPod/iPhone’s automatically.
If you do not have any iPod/iPhone units
1.) Press and hold the ‘FUNC/CL ADJ’ button for a few seconds, the hour digit in the display will start
flashing.
2.) Press the ‘TUNE+/SKIP+’ or ‘TUNE-/SKIP-‘ button to adjust the hour.
3.) When the correct hour is selected, press the ‘FUNC/CL.ADJ’ button again to enter the minute mode
with minute digit flashing.
4.) Press the ‘TUNE+/SKIP+’ or ‘TUNE-/SKIP-‘ button to adjust the minute.
5.) When the correct time is selected, press the ‘FUNC/CL ADJ’ button to store the time in the memory.
SETTING THE ALARM TIME
Before starting to set the alarm time, make sure that the unit is in POWER OFF mode.
1.) Press the ‘MEM+/AL1’ or ‘MEM/AL2’ button once (You can also use the ‘AL1’ or ‘AL2’ button on the
remote control) and the AL1 or AL2 icon will appear in the display.
2.) Press the ‘FUNC/CL. ADJ.’ button to select the alarm wake up source. You can choose buzzer,
iPod/iPhone, Radio or CD.
3.) Press and hold the ‘MEM+/AL1’ or ‘MEM/AL2’ button for a few seconds, the alarm hour digit will
begin flashing.
4.) Press the ‘TUNE+/SKIP+’ or ‘TUNE-/SKIP-‘ button to adjust the alarm hour.
5.) When the desired alarm hour is selected, press the ‘MEM+/AL1’ or ‘MEM/AL2’ button again, the
alarm minute digit will begin flashing.
6.) Press the ‘TUNE+/SKIP+’ or ‘TUNE-/SKIP-‘ button to adjust the alarm minute.
7.) When the desired alarm time is selected, press the ‘MEM+/AL1’ or ‘MEM/AL2’ button again to
confirm.
Note : If you choose iPod/iPhone or CD as the alarm wake up source, please make sure that you
havehave the iPod/iPhone or CD in place.
- 5 -