Pioneer VSX-9130TXH-K - Manual (Page 43)

The System Setup menu 07
43
En
Listen to the reference speaker and use it to measure the
target channel. From the listening position, face the two
speakers with your arms outstretched pointing at each
speaker. Try to make the two tones sound as if they are
arriving simultaneously at a position slightly in front of
you and between your arm span. 1
When it sounds like the delay settings are matched up,
press
 to confirm and continue to the next channel.
• For comparison purposes, the reference speaker will
change depending on which speaker you select.
• If you want to go back and adjust a channel, simply
use / to select it.
4 When you’re finished, press RETURN.
You will return to the Manual MCACC setup menu.
Standing Wave
• Default setting: ON 2 /ATT 0.0dB (all filters)
Acoustic standing waves occur when, under certain
conditions, sound waves from your speaker system
resonate mutually with sound waves reflected off the
walls in your listening area. This can have a negative
effect on the overall sound, especially at certain lower
frequencies. Depending on speaker placement, your
listening position, and ultimately the shape of your room,
it results in an overly resonant (‘boomy’) sound. The
Standing Wave Control uses filters to reduce the effect of
overly resonant sounds in your listening area. During
playback of a source, you can customize the filters used
for Standing Wave Control for each of your MCACC
presets.
3
1 Select ‘Standing Wave’ from the Manual MCACC
setup menu.
2 Adjust the parameters for the Standing Wave
Control.
• Filter Ch – Select the channel to which you will apply
the filter(s): MAIN (all except center channel and
subwoofer), Center or SW (subwoofer).
• TRIM (only available when Filter Ch above is SW) –
Adjust the subwoofer channel level (to compensate
for the difference in output post-filter).
• f / Q / ATT – These are the filter parameters where f
represents the frequency you will be targeting and Q
is the bandwidth (the higher the Q, the narrower the
bandwidth, or range) of the attenuation (ATT, the
amount of reduction to the targeted frequency).
3 When you’re finished, press RETURN.
You will return to the Manual MCACC setup menu.
Acoustic Calibration EQ Adjust
• Default setting: ON 2 /0.0dB (all channels/bands)
Acoustic Calibration Equalization is a kind of room equalizer
for your speakers (excluding the subwoofer). It works by
measuring the acoustic characteristics of your room and
neutralizing the ambient characteristics that can color the
original source material (providing a ‘flat’ equalization
setting). If you’re not satisfied with the adjustment provided
in Automatically setting up for surround sound (Auto
MCACC) on page 10 or Automatic MCACC (Expert) on
page 38, you can also adjust these settings manually to get
a frequency balance that suits your tastes.
4
1 Select ‘EQ Adjust’ from the Manual MCACC setup
menu.
2 Confirm that the MCACC preset shown in the display
is the one you want to adjust, then select START.
Note
1 • If you can’t seem to achieve this by adjusting the distance setting, you may need to change the angle of your speakers very slightly.
• For better audibility, the subwoofer emits a continuous test tone (oscillating pulses are heard from your other speakers). Note that it may be difficult to
compare this tone with the other speakers in your setup (depending on the low frequency response of the reference speaker).
2 You can switch on or off the Standing Wave Control and Acoustic Cal EQ feature in the AUDIO PARAMETER menu. See Setting the Audio options on
page 73 for more on this.
3 • Since they will be overwritten, you may want to save the standing wave settings made with the Auto MCACC Setup to another MCACC preset.
• Standing Wave control filter settings cannot be changed during playback of sources using the HDMI connection.
• When Standing Wave is selected for a MCACC preset memory where S-WAVE is set to OFF in the AUDIO PARAMETER, S-WAVE ON is automatically
selected.
3.Manual MCACC
:Return
a . Fine Channel Level
b . Fine SP Distance
c . Standing Wave
d . EQ Adjust
e . EQ Professional
MCACC : M1. MEMORY 1
Filter Ch SW
TRIM [ +12.0dB]
No. 1 2 3
f [ 63 Hz ] [ 110 Hz ] [ 250 Hz ]
Q [ 3.0 ] [ 8.0 ] [ 5.0 ]
ATT [ 2.5
dB ] [ 6.0 dB ] [ 6.0 dB ]
:Finish
3c.Standing Wave
4 When EQ Adjust is selected for a MCACC preset memory where EQ is set to OFF in the AUDIO PARAMETER, EQ ON is automatically selected.
3.Manual MCACC
:Return
a . Fine Channel Level
b . Fine SP Distance
c
. Standing Wave
d . EQ Adjust
e . EQ Professional
3d.EQ Adjust
MCACC : M1.MEMORY 1
[ START ]
ENTER:Next :Cancel
VSX-9130TXH_KU.book 43 ページ ２００８年４月１７日 木曜日 午前１１時２６分