Pioneer VSX-1018AH-K 7 - Manual (Page 84)

Additional information 13
84
En
Professional Calibration EQ graphical output
Display
Symptom Remedy
The EQ response displayed in
the graphical output following
calibration does not appear
entirely flat. • There are cases where the graph does not appear flat (even when selecting ALL CH ADJUST in the
Auto MCACC Setup) due to adjustments made to compensate for room characteristics to achieve
optimal sound.
• Areas of the graph may appear identical (before and after) when there is little or no adjustment
needed.
• The graph may appear to have shifted vertically when comparing before and after measurements.
EQ adjustments made using
the Manual MCACC setup on
page 41 do not appear to
change the graphical output. • Despite level adjustments being made, the filters used for analysis may not display these
adjustments in the graphical output. However, these adjustments are taken this into account by the
filters dedicated to overall system calibration.
Lower frequency response
curves do not seem to have
been calibrated for SMALL
speakers. • Low frequencies used in bass management (the subwoofer channel) will not change for speakers
that have been specified as SMALL in the configuration, or do not output these frequencies.
• Calibration is performed, but due to your speakers’ low frequency limitations, no measurable
sound is output for display.
Symptom Remedy
The display is dark or off. • Press DIMMER on the remote control repeatedly to select a different brightness.
After making an adjustment
the display goes off. • Press DIMMER on the remote control repeatedly to select a different brightness.
You can’t get DIGITAL to
display when using the
SIGNAL SEL button. • Check the digital connections and make sure that the digital inputs are assigned correctly (see The
Input Setup menu on page 67).
• If the multichannel analog inputs are selected, select a different input source.
The Dolby/DTS indicator
doesn’t light when playing
Dolby/DTS software. • These indicators do dot light if playback is paused.
• Check the playback (especially the digital output) settings of the source component.
When playing a DVD-Audio
disc, the DVD player display
shows 96 kHz. However, the
receiver’s display does not. • This is not a malfunction. 96 kHz audio from DVD-Audio discs is only output from the analog
outputs of the DVD player. This receiver cannot show the playback sample rate when using the
analog inputs.
During playback of a DTS 96/24
source, the display doesn’t
show 96 kHz. • Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 33).
When playing Dolby Digital or
DTS sources, the receiver’s
format indicators do not light. • Check that the player is connected using a digital connection.
• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 33).
• Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to PCM.
• Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is selected.
When playing certain discs,
none of the receiver’s format
indicators light. • The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on what
audio tracks are recorded on the disc.
When playing a disc with the
listening mode set to Auto
Surround, the
2 PL II or Neo:6
indicator lights on the receiver.
• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 33).
• If a two channel soundtrack is currently playing (including Dolby Surround encoded), then this is
not a malfunction. Check the disc packaging for details about the audio tracks available.
During playback of a Surround
EX or DTS-ES source on the
SBch AUTO setting, the EX
and ES indicators don’t light, or
the signal is not properly
processed. • The source may be Dolby Surround EX/DTS-ES software, but it has no flag to indicate it is 6.1
compatible. Set to SBch ON (see Using surround back channel processing on page 33), then switch
to the Standard EX listening mode (see Listening in surround sound on page 30).
During playback of DVD-Audio,
the display shows PCM. • This will occur when playing DVD-Audio material over the HDMI connection. This is not a
malfunction.
VSX-1018AH_KU.book 84 ページ ２００８年４月１７日 木曜日 午後２時３７分