Panasonic CF-T2 - Manual (Page 27)

27
T
roubleshooting
After the reinstallation procedure completes, this
screen should appear.
11 Remove the recovery CD and press any key to shut
down the computer, then remove the DVD-ROM & CD-
R/RW drive.
12 Turn the computer on, and press F2 while [Panasonic]
boot screen is displayed.
The Setup Utility will start up.
If the password has been set, enter the Supervisor Pass-
word.
13 Press F9 .
At the confirmation message, select [Yes] and press
Enter . (The Setup Utility settings will return to their
default values. Even the security settings with the ex-
ception of the password(s) will return to their default
values.)
14 Press F10 .
At the confirmation message, select [Yes] and press
Enter .
15 Perform the setup procedure for Windows by following
the instructions on the screen ( page 12).
16 Run the Setup Utility and change the settings where nec-
essary.
Do not interrupt the reinstallation procedure before
completion, for example by turning off the com-
puter or pressing Ctrl + Alt + Del , as this
may prevent Windows from starting up, or may
cause data to be lost so that the reinstallation proce-
dure cannot be executed.
When a message appears instructing you to insert
the next CD, insert the recovery CD showing the
next number in the sequence, and then select [OK].
If the message [The media does not contain the cor-
rect file] appears, select [OK]. A message will ap-
pear instructing you to insert the next CD.
Confirm that the proper recovery CD has been in-
serted by opening the cover of the DVD-ROM &
CD-R/RW drive and then close the cover, then se-
lect [OK].
CAUTION
Windows XP
Windows 2000
<When the hard disk backup function has been enabled>
If you select [3] in step 9 (
page 26) and execute reinstalla-
tion, the drive name for the second partition (data partition)
may be switched with that of the SD Memory Card. You can
still use the drives after the names have been switched, but
you can also return the drive names to their original state us-
ing the following procedures.
(The following procedure assumes that before reinstallation,
the second partition (data partition) was Drive E:, and the SD
Memory Card was Drive D:)
1 Disable the drive name for the second partition (data
partition).
1 In the menu below, select [Computer Management].
Windows XP
Select [start] - [Control Panel] - [Performance and Main-
tenance] - [Administrative Tools].
Windows 2000
Select [Start] - [Settings] - [Control Panel] - [Adminis-
trative Tools].
2 Select [Disk Management].
3 Right click on the partition for which [D:] is displayed
and select [Change Drive Letter and Paths...].
4 Select [Remove].
5 At the confirmation message, select [Yes].
2 Change the SD memory card drive name to [D:].
Use the SD drive name change tool to change the SD
Memory Card to the D: drive. (
"SD Memory
Card/ MultiMedia Card").
3 Set the drive name for the second partition (data partition)
as [E:].
1 In the menu below, select [Computer Management].
Windows XP
Select [start] - [Control Panel] - [Performance and Main-
tenance] - [Administrative Tools].
Windows 2000
Select [Start] - [Settings] - [Control Panel] - [Adminis-
trative Tools].
2 Select [Disk Management].
3 Right click on the partition for which the drive name is
not displayed, and select [Change Drive Letter and
Paths...].
4 Select [Add...], assign [E:] as the drive letter, and select
[OK].
10 At the confirmation message , press Y .
The operation of reinstallation for the hard disk starts
automatically. (The operations take about an hour.)
--------------------------------------------------------------------------
[Recovery] is complete.
Windows(R) XP Professional install wizard will start after reboot.
After turning off the power, please disconnect the CD/DVD-ROM drive, and
turn the power on again.
--------------------------------------------------------------------------
--------------------------------------------------------------------------
[Recovery] is complete.
Windows(R) 2000 Professional install wizard will start after reboot.
After turning off the power, please disconnect the CD/DVD-ROM drive, and
turn the power on again.
--------------------------------------------------------------------------