Roland EM-55 - Manual (Page 47)

EM-55 OR Owner’s Manual
47
ENGLISH
ENGLISH
ENGLISH
ENGLISH
OD ®Chors: This effect connects an Overdrive and
a Chorus in series. (“Series” means that the first
effect is also processed by the second.)
OD ®Flger: This effect connects an Overdrive and a
Flanger in series.
OD ®Delay: This effect connects an Overdrive and
a Delay in series.
DS ®Chors: This effect connects distortion and a
Chorus in series.
DS ®Flger: This effect connects distortion and a
Flanger in series.
DS ®Delay: This effect connects distortion and a
Delay in series.
EH ®Chors: This effect connects an Enhancer and
a Chorus in series.
EH ®Flger: This effect connects an Enhancer and a
Flanger in series.
EH ®Delay: This effect connects an Enhancer and
a Delay in series.
Cho ®Dly: This effect connects a Chorus and a
Delay in series.
FL ®Delay: This effect connects a Flanger and a
Delay in series.
Cho ®Flgr: This effect connects a Chorus and a
Flanger in series.
Cho/Dlay: This effect connects a Chorus and a
Delay in parallel. (“Parallel” means that the input
signal is processed by two effects that do not inter-
act.)
FL/Delay: This effect connects a Flanger and a
Delay in parallel.
Cho/Flgr: This effect connects a Chorus and a
Flanger in parallel.
■ M-FX UP1, UP2, LWR
(On/Off, Default setting: UP1: On, UP2/LWR: Off)
These parameters allow you to specify whether or
not the Upper 1, Upper 2, or Lower part should be
processed by the M-FX. See also p. 31.
■ Rev UP1
(0~127, Default setting: 100) This parameter
allows you to set the Reverb Send Level for Upper 1
(i.e. how much Reverb should be added to the
Upper 1 notes). This parameter is not used when
“M-FX UP1” is set to “On”.
■ Chr UP1
(0~127, Default setting: 0) This parameter allows
you to set the Chorus Send Level for Upper 1 (i.e.
how much Chorus should be added to the Upper 1
notes). If you want this part to be processed by the
Chorus effect, you need to select a value different
from “0”. This parameter is not used when “M-FX
UP1” is set to “On”.
■ Pan UP1
(0~127, Default setting: 64) This parameter allows
you to set the stereo position of the Upper 1 part
(i.e. its placement between the left and right speak-
ers). “0” means that the stereo position changes
randomly for each note you play. Values between
“1” and “63” correspond to the left speaker. “64”
refers to the center, and values between “65” and
“127” correspond to the right speaker (“1”= hard
left, “127”= hard right).
■ Rev UP2
(0~127, Default setting: 100) This parameter
allows you to set the Reverb Send Level for Upper 2
(i.e. how much Reverb should be added to the
Upper 2 notes). This parameter is not used when
“M-FX UP2” is set to “On”.
■ Chr UP2
(0~127, Default setting: 0) This parameter allows
you to set the Chorus Send Level for Upper 2 (i.e.
how much Chorus should be added to the Upper 2
notes). If you want this part to be processed by the
Chorus effect, you need to select a value different
from “0”. This parameter is not used when “M-FX
UP2” is set to “On”.
■ Pan UP2
(0~127, Default setting: 64) This parameter allows
you to set the stereo position of the Upper 2 part
(i.e. its placement between the left and right speak-
ers). “0” means that the stereo position changes
randomly for each note you play. Values between
“1” and “63” correspond to the left speaker. “64”
refers to the center, and values between “65” and
“127” correspond to the right speaker (“1”= hard
left, “127”= hard right).
■ Rev LWR
(0~127, Default setting: 100) This parameter
allows you to set the Reverb Send Level for the
Lower part. This parameter is not used when “M-FX
LWR” is set to “On”.
■ Chr LWR
(0~127, Default setting: 0) This parameter allows
you to set the Chorus Send Level for the Lower
part. If you want this part to be processed by the
Chorus effect, you need to select a value different
from “0”. This parameter is not used when “M-FX
LWR” is set to “On”.
■ Pan LWR
(0~127, Default setting: 64) This parameter allows
you to set the stereo position of the Lower part (i.e.
its placement between the left and right speakers).
“0” means that the stereo position changes ran-
domly for each note you play. Values between “1”
and “63” correspond to the left speaker. “64” refers
to the center, and values between “65” and “127”
correspond to the right speaker (“1”= hard left,
“127”= hard right).
■ Tone MFX
(On/Off, Default setting: On) This parameter allows
you to link the selection of an M-FX type to the
Tone you assign to the Upper 1 part. That way, a
Distortion/Overdrive effect will be selected for a
rock guitar sound, Rotary for an organ, etc.
■ FSW (Footswitch Assign)
(Default setting: Sustain) After connecting an
optional DP-2, DP-6, or BOSS FS-5U to the FOOT-
SWITCH/EXPR socket on the rear panel, you can use
this parameter for assigning a function to the foot-
switch.
Sustain VALUE
EM-55OR_UK Page 47 Wednesday, July 10, 2002 3:32 PM