ROTEL RMZ-955 - Manual (Page 9)

9
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Source connections
The RMZ-955 has four pair of RCA inputs for four source compo-
nents, as well as four pair of RCA “loop-through” outputs that
can send the source signals to other components.
Source inputs
Connect LINE LEVEL sources (CD player, tuner, etc.) to the
RMZ-955’s rear panel inputs as follows.
Using shielded RCA-RCA cables, connect the source’s output to
the corresponding source input on the RMZ-955. Connect analog
outputs from the source components as indicated to assure
clear operation with both the RR-952 hand held remote and the
RKP-901 keypad:
Tuner ➠ RMZ-955 Input 1
CD player ➠ RMZ-955 Input 2
Tape deck / DSS Satellite ➠ RMZ-955 Input 3
CD2 / VCR / DVD / LD ➠ RMZ-955 Input 4
Make sure to observe correct channel continuity from source to
RMZ-955. The RMZ-955’s RCA inputs are labelled for easy identi-
fication with Left Channel connections on the top row and Right
Channel connections on the bottom row.
Note 1: The RMZ-955 does not accept a phono cartridge’s output
directly. If required, use a separate phono preamp (such as
Rotel’s RQ-970BX) to boost phono signal to line level.
Note 2: Use only FIXED LEVEL source outputs to the RMZ-955.
Source outputs
Each source input on the RMZ-955 has a matching pair of “loop-
through” output RCA jacks. The primary use of these “loop-
through” outputs is to pass the signal from each source
component to additional RMZ-955 controllers in large multi-zone
systems (see page 15 for details on installing large systems).
In some cases, these “loop-through” outputs may alternatively
be used to “share” the source components with a separate
home theater or audio system. If the source is shared by another
system, connect each pair of RMZ-955 source outputs to the
appropriate inputs of the main system’s preamplifier as shown in
the hook-up illustration.
Note: The source sharing does not work with all combinations of
components. Specifically, home theater and audio systems with
micro-processor controlled source input switching may result in
problems such as interference or “mixing” between shared
sources.
TUNER CD AUX1 AUX2
INPUTS TAPE MONITOR
IN OUT LINE OUT
OUTPUT
RIGHT
LEFT
PREAMPLIFIER
TUNER
Tuner connected to Source 1 input (with optional pass-through to preamp for shared use with separate system).
INPUTS
2 3 4 1
IN OUT IN OUT IN OUT IN OUT
R
L
RC-5 N/C
MULTI-ZONE CUSTOM CONTROLLER
MODEL NO. RMZ-955
POWER CONSUMPTION: 430W
AC120V
~
60HZ
DESIGNED AND MANUFACTURED
IN ENGLAND
SPEAKER IMPEDANCE
4 OHM MINUMUM
TX-FORMAT
1 2 3 4 5 6
T
X
O
U
T
P
U
T
S
ZONE B
DATA
1 2 3 4 5 6
PRE-OUT
DATA
1 2 3 4 5 6
PRE-OUT
SPEAKERS SPEAKERS SPEAKERS SPEAKERS
ZONE D
DATA
1 2 3 4 5 6
PRE-OUT
DATA
1 2 3 4 5 6
PRE-OUT
ZONE C ZONE A
WE1
WE2
WE3
WE4
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
~ CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK
OF FIRE OR ELECTRICAL SHOCK DO
NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
– + – +
LEFT RIGHT
– + – +
LEFT RIGHT
– + – +
LEFT RIGHT
– + – +
LEFT RIGHT
PAGING
TRIGGER
AUDIO IN
AUDIO OUT
LINK IN
LINK OUT
UNSWITCHED SWITCHED
INSTALLATION: RMZ-955 CONTROLLER